This study reports on airborne exposure levels and soil concentrations of lead in regard to abatement of a steel structure (water tank). The tank was de-leaded by abrasive sand blasting. The ball of the tank had a lead surface level that exceeded the Environmental Protection Agency (EPA) definition of lead-based paint (LBP) (0.5% lead), but paint on stem and base was below this criterion. Personal and area airborne samples were collected during different activities of lead abatement of the tank. Summary results suggest during abrasive blasting of ball and stem/base personal exposure levels, as reported with arithmetic and geometric means, exceed the Occupational Safety and Health Administration (OSHA) permissible exposure limit (50 g/m3). Highest personal exposure (occupational exposure) was associated with blasting of ball. Distribution of airborne and soil samples suggest non-normality and is best represented by a logarithmic form. Geometric standard deviations for air and soil lead support a non-normal distribution. Outlying values were found for personal and area air samples. Exposure levels associated with blasting stem/base section of tank support OSHA’s policy requiring air monitoring of work at levels below the criterion established by EPA in identifying LBP. Area samples were statistically lower than personal samples associated with blasting ball and stem/base of tank. Exposure data suggest that workers performing abatement on steel structures have elevated lead exposure from surface lead. Respirator protection requirements are discussed. Soil lead concentration was suggested to decrease as distance increased from tank. Soil lead is suggested to be a result of deposition from LBP on tank surface. Minimal efforts were required to reduce average lead soil levels below EPA’s upper acceptable criterion (1200 ppm Pb).
Armstrong, B. G.1992: Confidence intervals for arithmetic means of lognormality distribution exposures. American Industrial Hygiene Association Journal53, 481-485.
2.
Booher, L. E.1988: Exposure in a ship overhaul facility during paint removal. American Industrial Hygiene Association Journal49, 121-127.
3.
Brown, S. K.2001: Air toxics in a New Australian dwelling over an 8-month period. Indoor-Built Environment10, 160-166.
4.
Conroy, L. M., Menezes-Lindsay, R. M., Sullivan, P. M., Cali, S. and Forst, L.1996. Lead, chromium, and cadmium exposure during abrasive blasting. Archives of Environmental Health51, 95-99.
5.
Corn, M.1983: Assessment and control of environmental exposure. Journal of Allergy and Clinical Immunology72, 231-241.
6.
Corn, M.1985: Strategies of air sampling. Scandanavian Journal of Work, Environment and Health11, 173-180.
7.
Chambers, C., Morris R., Salzman, D., Willis, T., Schnitzer, P., Brender, J. and Perrotta, D. M.1995: Epidemiological notes and reports lead poisoning among sandblasting workers - Galveston, Texas, March 1994. Morbidity and Mortality Weekly Report44, 44-45.
8.
Daniel, W. W.1991: Biostatistics: a foundation for analysis in the health sciences. New York: Wiley and Sons.
9.
US Environmental Protection Agency. 1984: Health effects assessment for lead. Cincinnati, OH: Office of Health and Environmental Assessment, EPA/540/1-86/055.
10.
US Environmental Protection Agency. 1997: Lead exposure associated with renovation and remodeling activities: environmental field sampling study, Volume I: technical report. EPA 747-R-96-007. Washington, DC.
11.
US Environmental Protection Agency. 2001: Lead; identification of dangerous levels of lead: final rule (40 CFR 745). Federal Register 66: 1205 - 12401. Washington, DC.
12.
Esmen, N. A. and Hammad, Y.1977: Log-normality of environmental sampling data. Journal of Environmental Science and HealthA12, 29-41.
13.
Esmen, N. A.1998: Exposure estimation in four major epidemiological studies in the acrylonitrile industry. Scandanavian Journal of Work, Environment and Health24, 63-70.
14.
Forst, L., Persky, V., Freels, S., Williams, R. and Conroy, L.1997: Lead exposure in ironworkers. American Journal of Industrial Medicine32, 540-543.
15.
Froines, J. R., Baron, S., Wegman, D. H. and O’Rourke, S.1990: Characterization of the airborne concentrations of lead in US Industry. American Journal of Industrial Medicine18, 1-17.
16.
Frumkin, H., Gerr, F., Castaaeda, F., Leal, A. and Santiago, L. R.1993: Lead poisoning in bridge demolition workers - Georgia, 1993. Morbidity and Mortality Weekly Report42, 388-390.
17.
Gersberg, R. M., Gaynor, K., Tenczar, D., Bartzen, M., Ginsberg, M., Gresham, L. S. and Molgaard, C.1997: Quantitative modeling of lead exposure from glazed ceramic pottery in childhood lead poisoning cases. International Journal of Environmental Health Research7, 193-202.
18.
Gidikova, P.1998: Air lead pollution and lead exposure of experimental animals and children in Stara Zagora (Bulgaria)International Journal of Environmental Health Research8, 303-313.
19.
Goldberg, M., Levin, S. M., Doucette, J. T. and Griffin, G.1997: A task-based approach to assessing lead exposure among ironworkers engaged in bridge rehabilitation. American Journal of Industrial Medicine31, 310-318.
20.
Grubbs, F. E.1950: Sample criteria for testing outlying observations. Annals of Maths and Statistics21, 27-58.
21.
Herut, B.2001: Levels of aerosol trace metals along the Mediterranean Coast of Israel 1996-87. Fresenius Environmental Bulletin10, 89-93.
22.
Hill, M. T. R., Dimitroulopoulou, C., Ashmore, M. R. and Batty, K.2001: Measurement and modeling of short-term variations in particle concentrations in UK homes. Indoor-Built Environment10, 132-137.
23.
Himmelstein, J., Wolkson, M., Pansky, G., Morse, D., Ross, H. A. and Gill, J.1993: Lead poisoning in bridge demolition workers - Massachusetts. Morbidity and Mortality Weekly Report38, 687-688, 693-694.
24.
Hunt, A., Hawkins, J., Gilligan, E. and Bhatia, S.1998: A comparison of the lead particle content of indoor dust before and after a lead paint abatement: a new source of lead recontamination. Indoor-Built Environment7, 32-46.
25.
Jacobs, D. E.1998: Occupational exposures to lead-based paint in structural steel demolition and residential renovations. International Journal of Environmental Pollution9, 1-14.
26.
Kaufman, J. D., Burt, J. and Silverstein, B.1994: Occupational lead poisoning: can it be prevented. American Journal of Industrial Medicine26, 701-712.
27.
Lange, J. H.1991: A suggested air standard for lead to protect the public during lead abatement. Medical Hypotheses36, 211-221.
28.
Lange, J. H.1999: A statistical evaluation of asbestos air concentrations. Indoor-Built Environment8, 293-303.
29.
Lange, J. H.2000: Health effects of respirator use at low airborne concentrations. Medical Hypotheses54, 1005-1007.
30.
Lange, J. H.2001a: Letter to the Editor, regarding Levels of aerosol trace metals along the Mediterranean Coast of Israel 1996-87. Fresenius Environmental Bulletin10, 741-742.
31.
Lange, J. H.2001b: Occupational exposure during removal of windows with lead-based paint and asbestos caulking. Bulletin of Environmental Contamination and Toxicology66, 146-149.
32.
Lange, J. H. and Thomulka, K. W.1994: Sampling and evaluation of soil for lead contamination: criteria for determining permissible concentrations in soil. Fresenius Environmental Bulletin3, 751-756.
33.
Lange, J. H. and Thomulka, K. W.1999: An evaluation of personal airborne asbestos exposure measurements during abatement of drywall and floor tile/mastic. International Journal of Environmental Health Research10, 5-19.
34.
Lange, J. H. and Thomulka, K. W.2000: Occupational exposure during lead abatement of steel surfaces by needle gun methodology. Bulletin of Environmental Contamination and Toxicology64, 463-466.
35.
Lange, J. H. and Thomulka, K. W.2000a: Occupational exposure to airborne asbestos during abatement of asbestos-containing pipe and boiler insulation. Fresenius Environmental Bulletin9, 477-482.
36.
Lange, J. H. and Thomulka, K. W.2000b: Effectiveness of engineering controls for airborne lead exposure during renovation/demolition of a commercial building. Indoor-Built Environment9, 207-215.
37.
Lange, J. H., Gretz, J. B., Wade, J. W. and Thomulka, K. W.1993: A pilot study of a small-scale lead-based paint abatement project that evaluated a blast machine which utilizes a soft recyclable plastic media: a case report. Fresenius Environmental Bulletin2, 671-676.
38.
Lange, J. H., Lange, P. R., Reinhard, T. K. and Thomulka, K. W.1996: A study of personal and area airborne asbestos concentrations during asbestos abatement: a statistical evaluation of fibre concentration data. The Annals of Occupational Hygiene40, 449-466.
39.
Lange, J. H., Sites, S. L. M. and Thomulka, K. W.1997: Personal sample measurements of airborne lead during abatement procedures. Bulletin of Environmental Contamination and Toxicology58, 659-666.
40.
Lange, J. H., Bruce, K. M., Johnson, R. L., Phillips, M. J., Smith, D. M. and Weidenboerner, K. M.1998: Survey of lead-based paint abatement projects in public building of Erie and Crawford Counties, Pennsylvania, USA. Regulatory Toxicology and Pharmacology: RTP28, 73-78.
41.
Lange, J. H., Sites, S. L. M. and Thomulka, K. W.1998a: Airborne lead exposure to workers during activity as part of a building demolition project. Indoor-Built Environment7, 210-216.
42.
Lange, J. H., Kuhn, B. D., Thomulka, K. W. and Sites, S. L. M.2000: A study of matched area and personal airborne asbestos samples: evaluation for relationship and distribution. Indoor-Built Environment9, 192-200.
43.
Leidel, N. A., Busch, K. A. and Lynch, J. R.1977: Occupational Exposure Sampling Strategy Manual. DEHW (NIOSH) Publication Number 77-173, National Technical Information Service Number PB-274-792. Cincinnati, OH: National Institute for Occupational Safety and Health, 1977.
44.
Letters to the Editor. 1998: A log-normal distribution-based exposure assessment method for unbalanced bias. The Annals of Occupational Hygiene42, 413-422.
45.
Levin, S. M., Goldberg, M. and Doucette, J. T.1997: The effect of the OSHA lead exposure in construction standard on blood lead levels among ironworkers employed in bridge rehabilitation. American Journal of Industrial Medicine31, 303-309.
46.
Linch, A. L., Weist, E. G. and Carter, M. D.1970: Evaluation of tetraethyl lead exposure by personal monitoring surveys. American Industrial Hygiene Association Journal31: 170-179.
47.
Maxim, L. D., Allshouse, J. N., Kelly, W. P., Walters, T., Waugh, R.1997: A multiyear workplace-monitoring program for refractory ceramic fibers: findings and conclusions. Regulatory Toxicological Pharmacology26, 156-171.
48.
Maxim, L. D., Allshouse, J. N. and Venturin, D. E.2000a: The random-effects model applied to refractory ceramic fiber data. Regulatory Toxicology and Pharmacology: RTP32, 190-199.
49.
Maxim, L. D., Allshouse, J. N., Kelly, M. P., Walters, T. and Waugh, R.2000b: A multiyear workplace-monitoring program for refractory ceramic fibers: findings and conclusions. Regulatory Toxicology and Pharmacology: RTP26, 156-171.
50.
Nayebzadeh, A, Cragg-Elkouh, S, Rancy, R. and Dufresne, A1999: Source of indoor air contamination on the ground floor of a high-rise commercial building. Indoor-Built Environment8, 237-345
51.
Nagyma, L., Desi, I., Schultz, H. and Papp, A.1998: Consequences of lead exposure of rats during pregnancy, lactation, and poisoning: a combined behavioural and neurotoxicological study. International Journal of Environmental Health Research8, 121-135.
52.
US Occupational Safety and Health Administration. 1993: Lead exposure in construction: interim final rule (29 CFR 1926.62). Federal Register58: 26590-26649. Washington, DC.
53.
US Occupational Safety and Health Administration. 1995: Interim interpretation concerning Type-CE respirators used in abrasive blasting that are manufactured by the E.D. Bullard Company, models 77 and 88, OSHA Standards Interpretation and Compliance Letters (8/30/95). Washington, DC.
54.
US Occupational Safety and Health Administration. 1996: General Industry requirements, 29 CFR 1910. Washington, DC.
55.
US Occupational Safety and Health Administration. 1999: Using X-ray fluorescence for analysis of lead in paint and applicability of other agencies lead levels. OSHA Standards Interpretation and Compliance Letters (3/01/99). Washington, DC.
56.
Rabin, R., Brooke, D. R. and Davis, L. K.1994: Elevated blood lead levels among construction workers in the Massachusetts occupational lead registry. American Journal of Public Health84, 1483-1485.
57.
Reynolds, S. J., Seem, R., Fourtes, L. J., Sprince, N. L., Johnson, J., Walkner, L., Clarke, W. and Whitten, P.1999: Prevalence of elevated blood leads and exposure to lead in construction trades in Iowa and Illinois. American Journal of Industrial Medicine36, 307-316.
58.
Reynolds, S. J., Fuortes, L. J., Garrels, R. L., Whitten, P. and Sprince, N. L.1997: Lead poisoning among construction workers renovating a previously deleaded bridge. American Journal of Industrial Medicine31, 319-323.
59.
Rom, W.1983: Environmental and occupational medicine. Boston, MA: Little, Brown and Company.
60.
Scheeper, B., Kromhout, H. and Boleij, S. M.1995: Wood-dust exposure during wood-working processes. The Annals of Occupational Hygiene39, 141-154.
61.
Seixas, N. S., Robins, T. G. and Moulton, L. H.1988: Use of geometric and arithmetic mean exposures in occupational epidemiology. American Journal of Industrial Medicine14, 465-477.
62.
Shapiro, S. S. and Wilk, M. B.1965: An analysis of variance test for normality. Biometrika52, 591-611.
63.
Spee, T. and Zwennis, W.1987: Lead exposure during demolition of steel structure coated with lead-based paints. Scandanavian Journal of Work, Environment and Health13, 52-61.
64.
Steenland, K. and Boffetta, P.2000: Lead and cancer in humans: where are we now?American Journal of Industrial Medicine38, 295-299.
65.
United States Court of Appeals. 1991: American iron and steel Institute and Bethlehem Steel Corporation vs. Occupational Safety and Health Administration. Federal Reporter Second Series (DC Cir.): 939, 975-1010.
66.
US Department of Health and Human Services (HUD). 1997: Update: blood lead levels - United States, 1991-1994. Morbidity and Mortality Weekly Report46, 141-146.
67.
United States Department of Housing and Urban Development 1995: Guidelines for the evaluation and control of lead-based paint hazards in housing. Washington, DC: United States Department of Housing and Urban Development.
68.
Vincent, L. D.1995: Abrasive blast media additives: a users perspective. Materials Performance34, 31-33.
69.
Vork, K. L., Hammond, S. K., Sparer, J. and Cullen, M. R.2001: Prevention of lead poisoning in construction workers: a new public health approach. American Journal of Industrial Medicine39, 243-253.
70.
Waller, K., Osorio, A. M. and Jones, J.1994: Lead exposure in a tank demolition crew: implications for the new OSHA construction lead standard. American Journal of Industrial Medicine26, 693-702.
71.
Zedd, H. C., Walker, Y. P., Hernandez, J. E. and Thomas, R. J.1993: Lead exposure during shipboard chipping and grinding paint-removal operations. American Industrial Hygiene Association Journal54, 392-396.
