Evaluation of plastic limit load of piping branch junctions subjected to out-of-plane moment loadings

Abstract

Under out-of-plane moment loadings, the piping branch junctions (also called tees in engineering) exhibit three kinds of failure mode, namely collapse failure of the branch pipe, global collapse of the intersection due to plastic hinges forming along the intersection line and local instability of the main pipe at the flank. In this work, the common piping branch junctions utilized in petrochemical and power industries with a failure mode of global collapse were investigated, and a new approximate formula for an out-of-plane plastic limit moment was presented. The formula was built on the following process: firstly, an equation between the out-of-plane limit moment and internal force of the branch pipe along the intersection is set up on the basis of the force equilibrium condition. Regarding this internal force as an external load for the main pipe shell, the internal force and moment along the intersection of the main pipe, under the plastic limit state, are then obtained. Finally, referring to the von Mises yield criterion, the approximate plastic limit load of the piping branch junctions subjected to the out-of-plane moment is derived. The accuracy of the new formula is validated by comparison with finite element analysis and experimental results.

Keywords

piping branch junction plastic limit load out-of-plane moment

Get full access to this article

View all access options for this article.

References

Xuan

F. Z.

P. N.

Liu

C. J.

Hui

Review of collapse limit load of nozzle/tee connection containing defects (in Chinese)

Chin. J. Pressure Vessel Technol., 2000, 17 (3), 65–71.

Ellyin

Out-of-plane limit couple of nozzle in cylindrical vessels or branch pipes in the tee connections. In 2nd International Conference on

Pressure Vessel Technology, Par 1, New York, 1973, pp. 253–267.

Schroeder

Limit intersection of external couples and internal pressure for branch-pipe lateral and tee connections. Part 1: Upper bounds to in-plane and out-of-plane limit couples applied to the branch for branch/pipe diameter ratio smaller than 0.8 In 2nd International Conference on

Pressure Vessel Technology, Part 1, New York, 1973, pp. 455–478.

Plancq

Berton

M. N.

Limit analysis based on elastic compensation method of branch pipe tee connection under internal pressure and out-of-plane moment loading

Int. J. Pressure Vessel and Piping, 1998, 75 (4), 819–825.

Chapuliot

Moulin

Plancq

Mechanical behavior of a branch pipe subject to out-of-plane bending load

Trans. ASME, J. Pressure Vessel Technol., 2002, 124 (1), 7–13.

Lynch

M. A.

Moffat

D. G.

Moretem

D. N.

Limit load for cracked piping branch junctions under pressure and branch out-of-plane bending

Int. J. Pressure Vessel and Piping, 2000, 77 (5), 185–194.

Schroeder

Plastic stability of pipes and tees exposed to external couples

WRC, 238, 1978.

Xuan

F. Z.

An engineering analysis for plastic limit load of pressurized piping branch junctions (in Chinese). PhD thesis, East China University of Science and Technology, Shanghai, China, 2002.

Rosenblium

V. I.

Plasticity conditions for thin shells, applied mathematics and mechanics

PMM, 1960, 24 (3), 364–366.

10.

Ellyin

Turkkan

Limit pressure of nozzles in cylindrical shells. In Winter Annual Meeting, New York, November 1972, ASME paper WA-PVP-1.

11.

Timoshenko

Woinowsky-Krieger

Theory of Plate and Shells, 2nd edition, 1959 (McGraw-Hill, New York).

12.

Ansary

El-Domiaty

Shabara

Short circumferential through-wall cracked pipes subjected to stretch-bending load

Nucl. Engng Des., 1998, 180 (2), 103–111.

13.

Schroeder

Analysis of test date on branch-pipe connections exposed to internal pressure and/or external couples

WRC, 1974, 200, 1–53.

14.

Ellyin

Experimental investigation of limit loads of nozzles in cylindrical vessels

WRC, 1976, 219, 1–21.

15.

Ellyin

An experimental study of elasto-plastic response of branch-pipe tee connections subjected to internal pressure, external couples and combined loadings

WRC, 1977, 230, 1–3.

16.

ANSI/API 579 Recommended Practice for Fitness-for-Service, 1997, Issue 6, p. F-2.