A novel eccentric lapping machine for finishing advanced ceramic balls

Abstract

Advanced ceramic balls are used extensively in hybrid precision ball bearings and show advantages in high speed, high temperature, high load and hostile environment. Finishing these balls with high quality, good efficiency and low cost is critical to their widespread application. A brief review of the methods for finishing ceramic balls is presented. The design of a novel eccentric lapping machine for finishing advanced ceramic balls is described. The kinematics of eccentric lapping is analysed and discussed, the symbolic expressions for the ball spin angular speed, ω_c, ball spin angle, β, and ball circulation angular speed, ω_c, are derived and numerical solutions are plotted. Two kinds of hot isostatically pressed (HIPed) silicon nitride ball blanks (13.25–13.50mm in diameter) were lapped and polished to 12.700 mm using this machine. A maximum material removal rate of 68 μm/h was achieved at the lapping step, which is much higher than by the traditional concentric lapping method. The polished ball surface roughness, R_a, value is 0.003 μm, and the ball roundness is 0.08–0.09 μm, which is above grade 5 and close to grade 3 of the precision bearing ball specification. This machine can be used as a prototype to develop a larger-scale machine for production.

Keywords

lapping machine finishing method eccentric lapping ceramic ball finishing silicon nitride hybrid bearings ball lapping mechanism

References

Cundill

R. T.

Light-weight material for the rolling elements of aircraft bearings. Ball Bearing J., 1983, 216, 33–36.

McColm

I. J.

Clark

N. J.

Forming, Shaping, and Working of High Performance Ceramics, 1988 (Blackie and Son Limited).

Tani

Kawata

Development of high-efficient fine finishing process using magnetic fluid. Ann. CIRP, 1984, 33, 217–220.

Umehara

Kato

Study on magnetic fluid grinding (1st report, The effect of the floating pad on removal rate of Si₃N₄ balls). Nippon Kikai Gakkai Ronbunshu, C Hen/Trans. Japan Soc. Mech. Engrs, Part C, 1988, 54, 1599–1604.

Umehara

Kato

Magnetic fluid grinding of advanced ceramic balls. Wear, 1996, 200, 148–153.

Childs

T. H. C.

Mahmood

Yoon

H. J.

Magnetic fluid grinding of ceramic balls. Tribology Int., 1995, 28, 341–348.

Jiang

Komanduri

On the finishing of Si₃N₄ balls for bearing applications. Wear, 1998, 215, 267–278.

Stolarski

T. A.

Jisheng

, Effect of water in oil based slurry on wear of silicon nitride. Br. Ceram. Trans., 1998, 97, 61–67.

Jisheng

Stolarski

T. A.

Gawne

T. Tribochemically assisted wear of silicon nitride ball. J. Eur. Ceram. Soc., 1996, 16, 25–34.

10.

Hah

S. R.

Fischer

T. E.

Tribochemical polishing of silicon nitride. J. Electrochem. Soc., 1998, 145, 1708–1714.

11.

Ichikawa

Ona

Yoshimoto

Kobayashi

Proposal of new lapping method for ceramic balls. Ann. CIRP, 1993, 42, 421–424.

12.

Kurobe

Kakuta

Onoda

Spin angle control lapping of balls (1streport)-theoretical analysis of lapping mechanism. Seimitsu Kogaku Kaishi/J. Japan Soc. for Precision Engng, 1996, 62, 1773–1777.

13.

Kurobe

Kakuta

Onoda

Spin angle control lapping of balls (2nd report)-lapping of silicon nitride ball. Seimitsu Kogaku Kaishi/J. Japan Soc. for Precision Engng, 1997, 63, 726–730.

14.

Childs

T. H. C.

Jones

D. A.

Mahmood

Zhang

Kato

Umehara

, Magnetic fluid grinding mechanics, Wear, 1994, 175, 189–198.

15.

Kang

Hadfield

Parameter optimization by Taguchi methods for finishing advanced ceramic balls using a novel eccentric lapping machine. Proc. Instn Mech. Engrs, Part B, Journal of Engineering Manufacture, 2001, 215(B1), 69–78.

16.

Kang

Hadfield

A study on the lapping of ceramic ball. In Surface Treatment IV-Computer Methods and Experimental Measurements, Assisi, Italy, 1999, pp. 389–399 (Computational Mechanics Publications, Southampton).

17.

Kang

Cundill

Hadfield

The consequences of aggressive lapping processes on the surface integrity of HIPed silicon nitride bearing balls. In Conference on Tribology in Environmental Design 2000, Bournemouth, 2000, pp. 227–234 (Professional Engineering Publishing Limited, Bury St Edmunds and London).