Effect and control of hatch length on material properties in the direct metal laser sintering process

Abstract

As one of the advanced rapid prototyping and manufacturing processes, the direct metal laser sintering (DMLS) process gives designers the possibility of building parts of almost any complexity in a wide range of metal materials. In DMLS, the sintered material is anisotropic and heterogeneous, affecting the quality and performance of the built parts. This paper presents a study that focuses on these two material characteristics and proposes a method to control them. Firstly, a series of experiments have been designed and conducted to study the influence of material anisotropy and heterogeneity on the built part strength. The heterogeneity was analysed and the microstructural changes due to different hatch line lengths were observed using scanning electron microscopy. The relationship between the hatch line length and the part quality is derived on the basis of experimental data collected and an appropriate statistical analysis applied. A genetic algorithm method is also proposed to optimize the hatch direction for obtaining more homogeneous sintered material properties. The experimental results verify that the negative effect of varying hatch lines in the early sintering process can be controlled effectively.

Keywords

direct metal laser sintering material properties anisotropy heterogeneity genetic algorithm

References

Ahn

S. H.

Montero

Odell

Roundy

Wright

P. K.

Anisotropic material properties of fused deposition modeling (FDM) ABS. Rapid Prototyping J., 2002, 8 (4), 248–257.

Corbel

Hinczewski

Chartier

Mechanical properties of ceramic parts made by stereolithography and sintering process. In Proceedings of the European Conference on Rapid Prototyping and Manufacturing, 1999, pp. 115–123.

Andrew

C. L.

David

W. R.

The effect of layer orientation on the tensile properties of net shape parts fabricated in stereolithography. In Proceedings of the Conference on Solid Freeform Fabrication, 2003, pp. 289–300.

Subramanian

P. K.

Vail

N. K.

Barlow

J. W.

Marcu

H. L.

Anisotropy in alumina produced by SLS. In Proceedings of the Conference on Solid Freeform Fabrication, 1994, pp. 330–338.

Gibson

Shi

D. P.

Material properties and fabrication parameters in selective laser sintering process. Rapid Prototyping J., 1997, 3 (4), 129–136.

Badrinarayan

Barlow

J. W.

Effect of processing parameters in SLS of metal-polymer powders. In Proceedings of the Conference on Solid Freeform Fabrication, 1995, pp. 55–63.

Beamen

J. J.

Solid Freeform Fabrication, A New Direction in Manufacturing, 1997 (Kluwer, Boston, Massachusetts).

Richard

H. C.

Computer aspects of solid freeform fabrication geometry, process control, and design. In Proceedings of the Conference on Solid Freeform Fabrication, 1993, pp. 102–112.

Rajan

V. T.

Vijay

Konstantinos

A. T.

The optimal zigzag direction for filling a two-dimensional region. Rapid Prototyping J., 2001, 7 (5), 231–241.

10.

Qiu

Langrana

N. A.

Danforth

S. C.

Safari

Jafari

Intelligent toolpath for extrusion-based LM process. Rapid Prototyping J., 2001, 7 (1), 18–23.

11.

Lin

Sun

Yan

A decomposition-accumulation model for layered manufacturing fabrication. Rapid Prototyping J., 2001, 7 (1), 24–31.

12.

Isaac

M. D.

Ori

Engineering Mechanics of Composite Materials, 1994 (Oxford University Press, New York).

13.

Standard E8-99, Standard test methods for tension testing of metallic materials. In Annual Book of ASTM Standards, 1999 (American Society of Testing and Standards, Philadelphia, Pennsylvania).

14.

Tang

Y. X.

Loh

H. T.

Fuh

Y. H. J.

Wong

Y. S.

Ning

Wang

X. H.

Accuracy analysis and improvement for direct laser sintering. Presented at the SMA Annual Symposium 2004, Singapore, January 2004.

15.

Manual of Instron Model 8501 Dynamic Testing System, 1990 (Instron Corporation, Canton, Massachusetts).

16.

Instructions of JSM-5500 Scanning Electron Microscope, 1999 (JESL Corporation, Jeol, Japan).

17.

Deltronic MPC-5 User Manual, 1998 (Deltronic Corporation, California).

18.

Zalzala

A. M. S.

Fleming

P. J.

Genetic Algorithms in Engineering Systems, 1997 (Institution of Electrical Engineers, London).

19.

Matthew

GAlib: A C++ library of genetic algorithm components, 1995, http://lancet.mit.edu/ga/.