Optimizing cutting parameters in minimum quantity of lubrication milling of hardened cold work tool steel

Abstract

Despite the numerous advantages offered by high-speed and high-performance cutting technologies, the issue of diminished tool life still remains profoundly concerning, especially in the case of machining hardened steels. Moreover, in finish machining, the requirement of improving workpiece surface finish also gains considerable importance. Application of the minimum quantity of lubrication (MQL) has delivered so many benefits that it has almost become part and parcel of turning, drilling, and milling technologies. In this research work, the high-speed milling of hardened cold work tool steel (62 HRc), under an MQL environment, was experimentally investigated and a response surface methodology was utilized to optimize the cutting parameters. A series of experiments was performed in order to quantify the effects of following three cutting parameters on tool life and arithmetic average surface roughness: cutting speed (V_c), feed rate (f_z), and radial depth of cut (a_e). The surface roughness was measured in two directions: along the feed, R_a, and along the pick-feed, R_a(pick). Analysis of variance (ANOVA) performed on the data revealed that the effect of cutting speed was significant on tool life as well as on R_a. Moreover, the effects of feed rate and radial depth of cut on tool life and R_a(pick) respectively were found to be significant. Scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS) analyses were performed to determine the dependence of different tool damage modes on levels of cutting parameters utilized. It was found that chipping and adhesion were the dominant tool damage modes in most of the experimental runs and their severity was dependent on levels of feed rate and cutting speed respectively.

Keywords

high-speed milling tool life surface roughness AISI D2 SEM

References

Schulz

, ‘Why high speed cutting?’. In International Conference on High speed machining, Nanjing, China, 2004, pp. 1–20. (2004).

Axinte

D. A.

Dewes

R. C.

, ‘Tool wear and workpiece surface integrity when high-speed ball nose end milling hardened AISI H13’. In 3rd International Conference on Metal cutting and HSM, Metz, France, 2001, pp. 171–179. (2001).

Axinte

D. A.

Dewes

R. C.

, ‘Surface integrity of hot work tool steel after high-speed milling—data and empirical models’ J. Mater. Process. Technol. 127 (2002): 325–335.

Iqbal

Khan

Dar

N. U.

, ‘Modeling the effects of cutting parameters in MQL-employed finish hard-milling process using D-optimal method’ J. Mater. Process. Technol. 199 (2008): 379–390.

Nagakawa

Akeda

Matsuoka

, ‘High speed milling of steel and tool life’. In 8th International Conference on Tool, die, and mold industry, Barcelona, Spain, 1995.(1995).

Quaile

, ‘Understanding MQL’, http://www.mmsonline.com/articles/010505.html.

Braga

D. U.

Diniz

A. E.

Miranda

G. W. A.

Coppinni

N. L.

, ‘Using a minimum quantity lubrication and a diamond coated tool in drilling of aluminum—silicon alloys’ J. Mater. Process. Technol. 122 (2002): 127–138.

Weinert

Inasaki

Sutherland

J. W.

Wakabayashi

, ‘Dry machining and minimum quantity lubrication’ Ann. CIRP 53 (2) (2004): 511–537.

Koshy

Dewes

R. C.

Aspinwall

D. K.

, ‘High speed end milling of hardened AISI D2 tool steel (58HRc)’ J. Mater. Process. Technol. 127 (2002): 266–273.

10.

Boehner

Dumitrescu

Elbastawi

M. A.

El-Wardany

T. I.

Chen

, ‘Effect of carbide tool grades and cutting edge geometry on tool life during high speed machining of hardened tool steel’. In 2nd International German and French Conference on High speed machining, Darmstadt, Germany, (1999), pp. 37–46.

11.

Yamada

Aoki

Kitaura

Tanaka

Okazaki

Hayasaki

, ‘High speed cutting performance of (Al, Ti)N coated carbide end mills for hardened steels’. In First French German Conference on High speed machining, Metz, France, (1997), pp. 486–489.

12.

Urbanski

J. P.

Koshy

Dewes

R. C.

Aspinwall

D. K.

, ‘High speed machining of moulds and dies for net shape manufacture’ Mater. Des. 21 (2000): 395–402.

13.

Coldwell

Woods

Paul

Koshy

Dewes

R. C.

Aspinwall

D. K.

, ‘Rapid machining of hardened AISI H13 and D2 moulds, dies and press tools’ J. Mater. Process. Technol. 135 (2003): 301–311.

14.

S.-P.

, ‘An adaptive-network based fuzzy inference system for prediction of workpiece surface roughness in end milling’ J. Mater. Process. Technol. 142 (2003): 665–675.

15.

Liao

Y. S.

Lin

H. M.

, ‘Mechanism of minimum quantity lubrication in high-speed milling of hardened steel’ Int. J. Mach. Tool. Mf. 47 (11) (2007): 1660–1666.

16.

Liao

Y. S.

Lin

H. M.

Chen

Y. C.

, ‘Feasibility study of the minimum quantity lubrication in high-speed end milling of NAK80 hardened steel by coated carbide tool’ Int. J. Mach. Tool Mf. 47 (11) (2007): 1667–1676.

17.

Iqbal

Khan

Dar

N. U.

, ‘Modeling the effects of cutting parameters in MQL-employed finish hard-milling process using D-optimal method’ J. Mater. Process. Technol. 199 (1–3) (2008): 379–390.

18.

Kang

M. C.

Kim

K. H.

Shin

S. H.

Jang

S. H.

Park

J. H.

Kim

, ‘Effect of the minimum quantity lubrication in high-speed end-milling of AISI D2 cold-worked die steel (62 HRC) by coated carbide tools’ Surf. Coat. Technol. 202 (22–23) (2008): 5621–5624.

19.

Iqbal

Xiao

M. H.

Qiu

B. G.

, ‘Refrigerated cooling air cutting of difficult-to-cut materials’ Int. J. Mach. Tool Mf. 47 (6) (2007): 927–933.

20.

Anderson

M. J.

Whitcomb

P. J.

, RSM simplified: Optimizing processes using response surface methods for design of experiments (Canada: Productive Publications Inc., Ontario 2004).

21.

Myers

R. H.

, Response surface methodology (Boston, Massachusetts: Allyn and Bacon Inc. 1971).