New die design for improvement of die corner filling in hydroforming of cylindrical stepped tubes

Abstract

Seamless tubular components, such as stepped tubes, conical tubes, and box shape tubes, are produced mainly in the tube hydroforming process. In forming the components in this process, complete filling of the die corners and obtaining a sharp corner is very difficult or even impossible. In this paper, the die corner filling in hydroforming of cylindrical stepped tubes was improved by a new die set. The proposed die was simulated and the filling of the die cavity was investigated. In order to verify the simulation results, the new die set was manufactured and some experiments were performed. It is shown that by using the new die set the parts with sharp corners and with more uniform thickness distribution could be produced. The simplicity of the die and low internal pressure are further advantages.

Keywords

tube hydroforming hydroforming die design stepped tubes finite element simulation

References

Koc

Allen

Jiratheranat

Altan

, ‘The use of FEA and design of experiments to establish design guideline for simple hydroforming parts’ Int. J. Mach. Tools Mf. 40 (2000): 2249–2266.

Kim

Kang

B.-S.

, ‘Implementation of backward tracing scheme of the FEM for design of initial tubular blank in hydroforming’ J. Mater. Processing Technol. 125–126 (2002): 839–848.

Koc

Altan

, ‘Application of two dimensional (2D) FEA for the tube hydroforming process’ Int. J. Mach. Tools Mf. 42 (2002): 1285–1295.

Koc

Altan

, ‘Predication of forming limits and parameters in the tube hydroforming process’ Int. J. Mach. Tools Mf. 42 (2002): 123–138.

Kridli

G. T.

Bao

Mallick

P. K.

Tian

, ‘Investigation of thickness variation and corner filling in tube hydroforming’ J. Mater. Processing Technol. 133 (2003): 287–296.

Fann

K. J.

Hsiao

P.-Y.

, ‘Optimization of loading conditions for tube hydroforming’ J. Mater. Processing Technol. 140 (2003): 520–524.

Hwang

Y. M.

Chen

W. C.

, ‘Analysis of tube hydroforming in a square cross-section die’ Int. J. Plasticity 21 (2005): 1815–1833.

Loh-Mousavi

Bakhshi-Jooybari

Mori

Hayashi

, ‘Improvement of formability in T-shape hydroforming of tubes by pulsating pressure’ Proc. IMechE, Part B: J. Engineering Manufacture 222 (B9) (2008): 1139–1146 DOI: 10.1243/09544054JEM1143.

Loh-Mousavi

Mori

Hayashi

Bakhshi-Jooybari

, ‘Improvement of filling of die corners in box-shaped tube hydroforming by control of wrinkling’ Key Engng Mater 344 (2007): 461–467.

10.

Elyasi

Bakhshi-Jooybari

Gorji

A. H.

Nourouzi

Alinejad

G. M.

, ‘Numerical and experimental investigation on forming metallic bellows in closed and open die hydroforming’ Steel Res. Int. 79 (S1) (2008): 148–154.

11.

Lee

S. W.

, ‘Study on the forming parameters of the metal bellows’ J. Mater. Processing Technol. 130–131 (2002): 47–53.

12.

Ngaile

Jaeger

Altan

, ‘Lubrication in tube hydroforming (THF) Part I. Lubrication mechanisms and development of model tests to evaluate lubricants and die coatings in the transition and expansion zones’ J. Mater. Processing Technol. 146 (2004): 108–115.