Nanofinishing of hard materials using micro-electrodischarge machining

Abstract

Micro-electrodischarge machining (micro-EDM) has been found to be an effective method of machining all types of conductive material, regardless of hardness. The process is being widely used in the production of tools and dies using hard and difficult-to-cut materials, where the surface quality of the product is of prime importance. The purpose of the present study is to investigate the feasibility of achieving fine surface finish in the micro-EDM of hard tungsten carbide (WC) and tool steel (SKH-51). Three different approaches: sinking, milling, and powder mixed dielectric (PMD) micro-EDM were applied in order to obtain a fine surface finish. The surface characteristics of machined WC and SKH-51 were studied and compared based on the surface topography achieved, the average surface roughness (R_a), and the peak-to-valley roughness (R_max) of the machined surface. It has been found that the topography and finish of the machined surface greatly depend on the discharge energy during machining. The surface generated using micro-EDM milling is found to be smoother and defect-free compared with those generated by die-sinking. At the same discharge energy, SKH-51 tool steel provides lower R_a and R_max when compared with WC. Finally, graphite PMD has been applied in the micro-EDM of SKH-51, as it provides comparatively lower R_a and R_max. It has been found that both the R_a and R_max were significantly reduced and crater distribution became more uniform when graphite nanopowder mixed dielectric was applied. Among the approaches, PMD milling micro-EDM has been found to provide a relatively improved surface finish during machining SKH-51.

Keywords

nanofinishing hard tool/die materials die-sinking micro-EDM milling micro-EDM PMD-micro-EDM RC generator graphite nanopowder mixed dielectric

References

Masuzawa

, ‘State of the art micromachining’ Ann. CIRP 49 (2) (2000): 473–488.

Singh

Maheshwari

Pandey

P. C.

, ‘Some investigations into the electrical discharge machining of hardened tool steel using different electrode materials’ J. Mater. Processing Technol. 149 (1–3) (2004): 272–277.

Koshy

Jain

V. K.

Lal

G. K.

, ‘Grinding of cemented carbide with electrical spark assistance’ J. Mater. Processing Technol. 72 (1) (1997): 61–68.

Lee

S. H.

X. P.

, ‘Study of the surface integrity of the machined workpiece in the EDM of WC’ J. Mater. Processing Technol. 139 (1–3) (2003): 315–321.

Guu

Y. H.

Hocheng

Chou

C. Y.

Deng

C. S.

, ‘Effect of electrical discharge machining on surface characteristics and machining damage of AISI D2 tool steel’ Mater. Sci. Engng A. 358 (1–2) (2003): 37–43.

Lee

L. C.

Lim

L. C.

Narayanan

Venkatesh

V. C.

, ‘Quantification of surface damage of tool steels after EDM’ Int. J. Mach. Tools Mf. 28 (4) (1988): 359–372.

Bleys

Kruth

J. P.

Lauwers

Schacht

Balasubramanian

Froyen

Humbeeck

J. V.

, ‘Surface and sub-surface quality of steel after EDM’ Adv. Engng Mater. 8 (1–2) (2006): 15–25.

Ghanem

Braham

Sidhom

, ‘Influence of steel type on electrical discharge machined surface integrity’ J. Mater. Processing Technol. 142 (1) (2003): 163–173.

Mohri

Saito

Higashi

M. A.

, ‘A new process of finish machining on free surface by EDM methods’ Ann. CIRP 40 (1) (1991): 207–210.

10.

Wong

Y. S.

Lim

L. C.

Rahuman

Tee

W. M.

, ‘Near-mirror-finish phenomenon in EDM using powder-mixed dielectric’ J. Mater. Processing Technol. 79 (1–3) (1998): 30–40.

11.

Tzeng

Y. F.

Lee

C. Y.

, ‘Effects of powder characteristics on electro discharge machining efficiency’ Int. J. Advd Mfg Technol. 17 (2001): 586–592.

12.

Schumacher

B. M.

, ‘About the role of debris in the gap during electrical discharge machining’ Ann. CIRP 39 (1) (1990): 197–199.

13.

Narumiya

Mohri

Saito

Otake

Tsnekawa

Takawashi

Kobayashi

, ‘EDM by powder suspended working fluid’ (1989).

14.

Zhao

W. S.

Meng

Q. G.

Wang

Z. L.

, ‘The application of research on powder mixed EDM in rough machining’ J. Mater. Processing Technol. 129 (2002): 30–33.

15.

Erden

Bilgin

, ‘Role of impurities in electric discharge machining’ In Proceedings of the 21st International Machine Tool Design and Research Conference, Swansea, (1980), pp. 345–350 (Macmillan, London).

16.

Jeswani

M. L.

, ‘Effects of the addition of graphite powder to kerosene used as the dielectric fluid in electrical discharge machining’ Wear 70 (1981): 133–139.

17.

Kobayashi

Magara

Ozaki

Yatomi

, ‘The present and future developments of electrical discharge machining’ In Proceedings of the 2nd International Conference on Die and mould technology, Singapore, (1992), pp. 35–47.

18.

Tzeng

Y. F.

Chen

F. C.

, ‘Investigation into some surface characteristics of electrical discharge machined SKD-11 using powder-suspension dielectric oil’ J. Mater. Processing Technol. 170 (1–2) (2005): 385–391.

19.

K. L.

Yan

B. H.

Huang

F. Y.

Chen

S. C.

, ‘Improvement of surface finish on SKD steel using electro-discharge machining with aluminum and surfactant added dielectric’ Int. J. Mach. Tools Mf. 45 (10) (2005): 1195–1201.

20.

Yan

B. H.

Chen

S. L.

, ‘Characteristics of SKD11 by complex process of electrical discharge machining using liquid suspended with alumina powder’ Nippon Kinzoku Gakkaishi, J. Jap. Inst. Metals 58 (9) (1994): 1067–1072.

21.

Tan

P. C.

Yeo

S. H.

Tan

Y. V.

, ‘Effects of nano-sized powder additives in dielectric in micro-EDM’ In Proceedings of the Asian Symposium on Precision engineering and nanotechnology, 6–9 November 2007, Gwangju, Korea, pp. 105–109.

22.

Jung

J. W.

S. H.

Jeong

Y. H.

Min

B. K.

Lee

S. J.

, ‘Estimation of material removal volume of a micro-EDM drilled hole using discharge pulse monitoring’ Int. J. Precision Engng Mfg 8 (4) (2007): 45–49.

23.

Lim

H. S.

Wong

Y. S.

Rahman

Lee

E. M. K.

, ‘A study on the machining of high-aspect ratio micro-structures using micro EDM’ J. Mater. Processing Technol. 140 (2003): 318–325.

24.

Jahan

M. P.

Wong

Y. S.

Rahman

, ‘A study on the fine-finish die-sinking micro-EDM of tungsten carbide using different electrode materials’ J. Mater. Processing Technol. 209 (8) (2009): 3956–3967 DOI: 10.1016/ j.jmatprotec.2008.09.015.

25.

Jahan

M. P.

Wong

Y. S.

Rahman

, ‘A comparative study of transistor and RC pulse generators for micro-EDM of tungsten carbide’ Int. J. Precision Engng Mfg 6 (4) (2008): 3–10.

26.

Kunieda

Lauwers

Rajurkar

K. P.

Schumacher

B. M.

, ‘Advancing EDM through fundamental insight into the process’ Ann. CIRP 54 (2) (2005): 599–622.

27.

Han

Wachi

Kunieda

, ‘Improvement of machining characteristics of micro-EDM using transistor type isopulse generator and servo feed control’ Precision Engng 28 (4) (2004): 378–385.

28.

Pecas

Henriques

, ‘Influence of silicon powder-mixed dielectric on conventional electrical discharge machining’ Int. J. Mach. Tools Mf. 43 (14) (2003): 1465–1471.

29.

Masuzawa

Cui

Taniguchi

, ‘Improved jet flushing for EDM’ Ann. CIRP 41 (1) (1992): 239–242.

30.

Lonardo

P. M.

Bruzzone

A. A.

, ‘Effect of flushing and electrode material on die sinking EDM’ Ann. CIRP 48 (1) (1999): 123–126.

31.

Kansal

H. K.

Singh

Kumar

, ‘Technology and research developments in powder mixed electric discharge machining (PMEDM)’ J. Mater. Processing Technol. 184 (1–3) (2007): 32–41.