High-speed milling of AISI H13 hot-work tool steel using polycrystalline cubic boron nitride ball-nose mills: From experimental investigations and empirical modelling to functional testing of the machined surfaces

Abstract

Owing to continuous development of composite materials, the properties of polycrystalline cubic boron nitride (PCBN) can be engineered to enable their use for the manufacture of cutting edges for high-speed machining applications. This paper reports on an ‘integrative’ approach, i.e. cutting parameters—tool performance—surface integrity and residual stresses—tribological and fatigue assessment, of the high-speed milling (HSM) of AISI H13 hot-work tool steel using PCBN ball-nose end milling cutters. The experimental trials followed an experimental design (factors: cutting speed, feed per tooth, workpiece tilt angle) on which a set of key process output measures was examined: tool life, surface roughness, metallurgical integrity, microhardness, and residual stresses. Where significant variations in the output measures with the changes in the operating parameters were found, empirical models were generated; this is of particular importance for the mould/die industry to enable the prediction of critical process measures such as tool flank wear, surface roughness, and residual stresses under machined surfaces without the need for repeated measurements. It was found that only a compromise of the ‘near-best’ values of the output measures can be obtained by employing a ‘pseudo-optimal’ set of cutting parameters. Further, functional tests carried out on HSM surfaces with ‘near-best’ output measures using PCBN tools showed that superior fatigue performance (approximately 30 per cent) is expected for moulds/dies when compared with those obtained via the conventional manufacturing route (electrical discharge machining and polishing).

Keywords

high-speed milling polycrystalline cubic boron nitride hot-work tool steel tool performance surface roughness surface integrity empirical modelling tribological and fatigue testing

References

Dewes

R. C.

, High speed machining of hardened ferrous alloys. PhD Thesis, University of Birmingham, Birmingham, UK, 1997.

Dewes

R. C.

Chua

K. S.

Newton

P. G.

Aspinwall

D. K.

, ‘Temperature measurements when high speed machining hardened mould/die steel’ J. Mater. Processing Technol. 92–93 (1999): 293–301.

Barry

Akdogan

Smyth

McAvinue

O'Halloran

, ‘Application areas for PCBN materials’ Industrial Diamond Rev. 3 (2006): 46–53.

Elbestawi

M. A.

Chen

Becze

C. E.

El-Wardany

T. I.

, ‘High-speed milling of dies and moulds in their hardened state’ Ann. CIRP 46 1 (1997): 57–62.

Dewes

R. C.

Aspinwall

D. K.

Dipple

S. D.

Schoen

Thielmann

, ‘Tool wear and surface integrity observations during the high speed milling of hardened die steel’ (1997).

Tönshoff

H. K.

Gey

Tønnessen

Sørby

, ‘High speed flank milling of Greek Ascoloy—the effect of cooling lubrication on tool wear, cutting forces and surface integrity’ (2000).

Wang

Z. G.

Wong

Y. S.

Rahman

, ‘High-speed milling of titanium alloys using binderless CBN tools’ Int. J. Mach. Tools and Mf. 45 1 (2005): 105–114.

Hideharu

Kazuhiro

Hitoshi

, ‘Cutting performance of a binder-less sintered cubic boron nitride tool in the high-speed milling of gray cast iron’ J. Mater. Processing Technol. 127 2 (2002): 217–221.

Bieker

, ‘High-speed die milling with PCBN’ Industrial Diamond Rev. 1 (1995): 1–3.

10.

Elbestawi

M. A.

Chen

Becze

C. E.

El-Wardany

T. I.

, ‘High-speed milling of dies and models in their hardened state’ Ann. CIRP—Mfg Technol. 46 1 (1997): 57–62.

11.

Braghini

Coelho

R. T.

, ‘An investigation of the wear mechanisms of polycrystalline cubic boron nitride (PCBN) tools when end milling hardened steels at low/medium cutting speeds’ Int. J. Advd Mfg Technol. 17 4 (2001): 244–251.

12.

Koshy

Dewes

R. C.

Aspinwall

D. K.

, ‘High speed end milling of hardened AISI D2 tool steel (similar to 58 HRC)’ J. Mater. Processing Technol. 127 2 (2002): 266–273.

13.

BS 6861: Part 1/1987: Balance quality requirements of rigid rotors: Part 1. Method for determination of permissive residual unbalance.

14.

Axinte

D. A.

Dewes

R. C.

, ‘Surface integrity of hot work tool steel after high speed milling—experimental data and empirical models’ J. Mater. Processing Technol. 127 3 (2002): 325–335.

15.

Axinte

D. A.

Dewes

R. C.

, Mathematical modelling of the surface integrity of forging dies manufactured by high speed machining, Internal report, University of Birmingham, Birmingham, UK, 2001.