On-machine fabrication of high-aspect-ratio micro-electrodes and application in vibration-assisted micro-electrodischarge drilling of tungsten carbide

Abstract

The concept of fabricating on-machine high-aspect-ratio micro-electrodes arises from the need to fabricate small and deep micro-holes in micro-electrical discharge machining (micro-EDM). In the present study, investigations are conducted on the fabrication of high-aspect-ratio micro-electrodes using two simple and cost-effective micro-EDM-based processes: the ‘turning-μEDM’ hybrid process and the ‘moving-electrode-block-μEDM’ process. Process descriptions and important aspects for successful fabrication of high-aspect-ratio micro-electrodes are discussed. In addition, the application of these micro-electrodes in the fabrication of deep micro-holes in tungsten carbide using normal micro-EDM and vibration-assisted micro-EDM is presented. It is found that the turning-μEDM process can generate finer micro-electrodes for easily machinable materials such as brass, but its application to the machining of deep micro-holes in tungsten Carbide is limited by the extreme tool wear of the brass electrode. The block-μEDM process can generate microelectrodes with hard, difficult-to-cut, and high-melting-point materials such as copper tungsten (alloy) and tungsten with much higher aspect ratios. However, the taper angle of the fabricated micro-electrodes is a common problem in the stationary block-μEDM process. This problem is reduced to a great extent by using block-μEDM with a moving electrode. Micro-holes with an aspect ratio of 16.7 are achieved using vibration-assisted micro-EDM with the fabricated tungsten micro-electrode machined by the moving-electrode-block-μEDM process.

Keywords

high-aspect-ratio micro-electrodes turning-μEDM hybrid process block-μEDM process vibration-assisted micro-EDM tungsten carbide

References

Richardson

M. T.

Gianchandani

Y. B.

, ‘Achieving precision in high density batch mode micro-electro-discharge machining’ J. Micromech. Microengng. 18 (2008): 015002.

Masaki

Kawata

Masuzawa

, ‘Micro electro-discharge machining and its applications’. In Proceedings of the IEEE conference on Micro electro mechanical systems, Napa Valley, California, 11–14 February 1990, pp. 21–26 (IEEE, Piscataway, New Jersey).

K. H.

Newman

S. T.

, ‘State of the art electrical discharge machining (EDM)’ Int. J. Mach. Tools Mf., 43 (2003): 1287–1300.

Rajurkar

K. P.

Z. Y.

, ‘3D micro-EDM using CAD/CAM’ Ann. CIRP 49 (1) (2000): 127–130.

Z. Y.

Masuzawa

Fujino

, ‘3D micro-EDM with simple shape electrode: Part 1’ Int. J. Electr. Machining, 3 (1998): 7–12.

Z. Y.

Masuzawa

Fujino

, ‘3D micro-EDM with simple shape electrode: Part 2’ Int. J. Electr. Machining, 3 (1998): 71–79.

Mohri

Takezawa

Furutani

Ito

Sata

, ‘A new process of additive and removal machining by EDM with a thin electrode’ Ann. CIRP 49 (1) (2000): 123–126.

Yeo

S. H.

Nachiappan

, ‘Investigation of micro-EDM controllable factors on machined silicon surface quality’ Proc. IMechE, Part B: J. Engineering Manufacture 215 (B6) (2001): 811–817.

Ravi

Chuan

S. X.

, ‘The effects of electro-discharge machining block electrode method for microelectrode machining’ J. Micromech. Microengng 12 (5) (2002): 532–540.

10.

Masuzawa

Fujino

Kobayashi

Suzuki

, ‘Wire electro-discharge grinding for micro machining’ Ann. CIRP 34 (1) (1985): 431–434.

11.

Kim

B. H.

Park

B. J.

Chu

C. N.

, ‘Fabrication of multiple electrodes by reverse EDM and their application in micro ECM’ J. Micromech. Microengng 16 (4) (2006): 843–850.

12.

Masuzawa

Tonshoff

H. K.

Zentrum

, ‘Three dimensional micromachining by machine tools’ Ann. CIRP 46 (2) (1997): 621–628.

13.

Takahata

Gianchandani

Y. B.

, ‘Batch mode micro-electro-discharge machining’ J. Microelectromech. Syst. 11 (2) (2002): 102–110.

14.

Takahata

Shibaike

Guckel

, ‘A novel micro electro-discharge machining method using electrodes fabricated by the LIGA process’. In Proceedings of the IEEE Conference on Micro electro mechanical systems, Orlando, Florida, 17–21 January 1999, pp. 238–243 (IEEE, Piscataway, New Jersey).

15.

Liu

Rahman

Wong

Y. S.

, ‘Micro machining of silicon by electrical discharge machining’ SME technical paper MR01-237, 2001, pp 1–7.

16.

Matsui

Kaito

Fujita

J.-I.

Ishida

Ochiai

, ‘Three-dimensional nanostructure fabrication by focused-ion-beam chemical vapor deposition’ J. Jpn Soc. Precis. Engng 67 (9) (2001): 1412–1415. -(in Japanese).

17.

Ravi

Huang

, ‘Fabrication of symmetrical section microfeatures using the electro-discharge machining block electrode method’ J. Micromech. Microengng 12 (6) (2002): 905–910.

18.

Asad

A. B. M. A.

Masaki

Rahman

Lim

H. S.

Wong

Y. S.

, ‘Tool-based micro-machining’ J. Mater. Process. Technol., 192–193 (2007): 204–211.

19.

Rahman

Lim

H. S.

Neo

K. S.

Kumar

A. S.

Wong

Y. S.

X. P.

, ‘Tool-based nanofinishing and micromachining’ J. Mater. Process. Technol. 185 (1–3) (2007): 2–16.

20.

Lim

H. S.

Kumar

A. S.

Rahman

, ‘Improvement of form accuracy in hybrid machining of microstructures’ J. Electron. Mater. 31 (10) (2002): 1032–1038.

21.

Lim

H. S.

Wong

Y. S.

Rahman

Lee

E. M. K.

, ‘A study on the machining of high-aspect ratio micro-structures using micro’ EDM. J. Mater. Process. Technol. 140 (1–3) (2003): 318–325.

22.

Rahman

M. A.

Rahman

Kumar

A. S.

Lim

H. S.

Asad

A. B. M. A.

, ‘Development of micropin fabrication process using tool based micromachining’ Int. J. Adv. Mfg. Technol. 27 (9–10) (2006): 939–944.

23.

Jahan

M. P.

Wong

Y. S.

Rahman

, ‘A comparative study of transistor and RC pulse generators for micro-EDM of tungsten carbide’ Int. J. Precis. Engng Mf. 9 (4) (2008): 3–10.

24.

Jahan

M. P.

Wong

Y. S.

Rahman

, ‘A study on the fine-finish die-sinking micro-EDM of tungsten carbide using different electrode materials’ J. Mater. Process. Technol. 209 (8) (2009): 3956–3967.

25.

Yan

B. H.

Huang

F. Y.

Chow

H. M.

Tsai

J. Y.

, ‘Micro-hole machining of carbide by electrical discharge machining’ J. Mater. Process. Technol. 87 (1–3) (1999): 139–145.

26.

Wansheng

Zhenlong

Shichun

Guanxin

Hongyu

, ‘Ultrasonic and electric discharge machining to deep and small hole on titanium alloy’ J. Mater. Process. Technol. 120 (1–3) (2002): 101–106.

27.

Gao

Liu

, ‘A study of ultrasonically aided micro-electrical discharge machining by the application of workpiece vibration’ J. Mater. Process. Technol. 139 (1–3) (2003): 226–228.

28.

Chern

G. L.

Chuang

, ‘Study on vibration-EDM and mass punching of micro-holes’ J. Mater. Process. Technol. 180 (1–3) (2006): 151–160.

29.

Tong

Wang

, ‘Experimental research on vibration assisted EDM of micro-structures with non-circular cross-section’ J. Mater. Process. Technol. 208 (1–3) (2008): 289–298.