Modelling and experimental investigation on the effect of nanopowder-mixed dielectric in micro-electrodischarge machining of tungsten carbide

Abstract

Micro-electrodischarge machining (micro-EDM) is one of the most effective methods used in die and mould industries for machining difficult-to-cut tool and die materials such as tungsten carbide (WC). The quality and integrity of the surface finish resulting from the micro-EDM process in die and mould making can have a significant impact on the product performance. The present study intends to investigate the feasibility of improving the surface finish in micro-EDM of WC in a dielectric mixed with graphite (Gr), aluminium (Al), and alumina (Al₂O₃) nanopowders. The mechanism of powder-mixed micro-EDM is presented theoretically in terms of the effect of additive powder characteristics on the dielectric breakdown and gap width. In addition, the effect of the nanopowders’ mixed dielectric on surface topography, average surface roughness (R _a), peak-to-valley roughness (R _max), material removal rate (MRR), and electrode wear ratio (EWR) was studied experimentally. It has been shown theoretically that the presence of a conductive or semi-conductive powder lowers the breakdown strength and increases the spark gap during powder-mixed micro-EDM. The surface finish and topography was improved significantly owing to the increased spark gap and uniform discharging in powder-mixed micro-EDM. In addition, the lower breakdown strength of dielectric and increased spark gap contribute to higher MRR and lower EWR in addition to improved surface finish. Among the three types, semi-conductive graphite nanopowder was found to provide a smooth and shiny surface with lower R _a and R _max, whereas the spark gap and MRR was found to be higher when aluminium powder was used. The non-conductive alumina powder was found to have very little effect on the performance of powder-mixed micro-EDM of WC. Finally, from analytical and experimental study, it has been concluded that the particle size, concentration, density, and thermal and electrical conductivity of powder materials are the most influencing factors in powder-mixed micro-EDM of WC.

Keywords

nanopowder-mixed dielectric fine-finish micro-EDM modelling surface finish powder characteristics tungsten carbide.

References

Mahdavinejad

R. A.

Mahdavinejad

ED machining of WC-Co. J. Mater. Process. Technol. 2005, 162–163, 637–643

Casas

Torres

Llanes

Fracture and fatigue behavior of electrical discharge machined cemented carbides. Int. J. Refract. Metals Hard Mater. 2006, 24, 162–167

Koshy

Jain

V. K.

Lal

G. K.

Grinding of cemented carbide with electrical spark assistance. J. Mater. Process. Technol. 1997, 72, 61–68

Ramasawmy

Blunt

3D surface topography assessment of the effect of different electrolytes during electrochemical polishing of EDM surfaces. Int. J. Mach. Tools Mf 2002, 42, 567–574

Tzeng

Y. F.

Chen

F. C.

Investigation into some surface characteristics of electrical discharge machined SKD-11 using powder-suspension dielectric oil. J. Mater. Process. Technol. 2005, 170, 385–391

Wong

Y. S.

Lim

L. C.

Rahuman

Tee

W. M.

Near-mirror-finish phenomenon in EDM using powder-mixed dielectric. J. Mater. Process. Technol. 1998, 79, 30–40

Zhao

W. S.

Meng

Q. G.

Wang

Z. L.

The application of research on powder mixed EDM in rough machining. J. Mater. Process. Technol. 2002, 129, 30–33

Tzeng

Y. F.

Lee

C. Y.

Effects of powder characteristics on electro discharge machining efficiency. Int. J. Advd Mfg Technol. 2001, 17, 586–592

Kansal

H. K.

Singh

Kumar

Parametric optimization of powder mixed electrical discharge machining by response surface methodology. J. Mater. Process. Technol. 2005, 169, 427–436

10.

Uno

Okada

Surface generation mechanism in electrical discharge machining with silicon powder mixed fluid. Int. J. Electl Mach. 1997, 2, 13–18

11.

Uno

Okada

Hayashi

Tabuchi

Surface integrity in EDM of aluminum bronze with nickel powder mixed fluid. J. Jap. Soc. Electl Mach. 1998, 32, 24–31

12.

Erden

Bilgin

Role of impurities in electric discharge machining In Proceedings of 21st International Conference on Machine tool design and research 1980, 345–350(Macmillan London)

13.

Jeswani

M. L.

Effects of the addition of graphite powder to kerosene used as the dielectric fluid in electrical discharge machining. Wear 1981, 70, 133–139

14.

Mohri

Saito

Higashi

M.A.

A new process of finish machining on free surface by EDM methods. CIRP Annls 1991, 40 (1), 207–210

15.

Narumiya

Mohri

Saito

Otake

Tsnekawa

Takawashi

Kobayashi

EDM by powder suspended working fluid. In Proceedings of 9th ISEM Nagaya, Japan 1989, 5–8

16.

Kobayashi

Magara

Ozaki

Yatomi

The present and future developments of electrical discharge machining In Proceedings of 2nd International Conference on Die and mould technology 1992, Singapore 35–47

17.

Yan

B. H.

Chen

S. L.

Characteristics of SKD11 by complex process of electric discharge machining using liquid suspended with aluminum powder. J. Jap. Inst. Light Metals 1994, 58 (9), 1067–1072

18.

Wang

C. H.

Lin

Y. C.

Yan

B. H.

Huang

F. Y.

Effect of characteristics of added powder on electric discharge machining. J. Jap. Inst. Light Metals 2001, 42 (12), 2597–2604

19.

Pecas

Henriques

E.A.

Influence of silicon powder mixed dielectric on conventional electrical discharge machining. Int. J. Mach. Tools Mf. 2003, 43, 1465–1471

20.

Çogun

Özerkan

Karaçay

An experimental investigation on the effect of powder mixed dielectric on machining performance in electric discharge machining. Proc IMechE, Part B: J. Engineering Manufacture 2006, 220 (8), 1035–1050 DOI: 10.1243/09544054JEM320

21.

Chow

H. M.

Yan

B. H.

Huang

F. Y.

Hung

J. C.

Study of added powder in kerosene for the micro-slit machining of titanium alloy using electro-discharge machining. J. Mater. Process. Technol. 2000, 101, 95–103

22.

Tan

P. C.

Yeo

S. H.

Tan

Y. V.

Effects of nano-sized powder additives in micro-Electrical Discharge Machining. Int. J. Precision Engng Mf 2008, 9, 22–26

23.

Kurnia

Tan

P. C.

Yeo

S H.

Tan

Q. P.

Surface roughness model for micro electrical discharge machining. Proc IMechE, Part B: J. Engineering Manufacture, 223 (3), 279–287 DOI: 10.1243/09544054JEM1188

24.

Pradhan

M. K.

Das

Biswas

C. K.

Comparisons of neural network models on surface roughness in electrical discharge machining. Proc IMechE, Part B: J. Engineering Manufacture, 223 (B7), 801–808 DOI: 10.1243/09544054JEM1367

25.

Rubinow

S. I.

Keller

J. B.

The transverse force on a spinning sphere moving in a viscous fluid. J. Fluid Mech. 1961, 11, 447–459

26.

Kok

J. A.

Electrical breakdown of insulating liquids 1961, 43–45(Centrex Publishing Company Einhoven)

27.

Ushakov

V. Y.

Insulation of high-voltage equipment 2004, first edition, Germany

Springer

65–70

28.

Chatterton

P. A.

Menon

M. M.

Srivastava

K. D.

Processes involved in the triggering of vacuum breakdown by low velocity microparticles. J. Appl. Phys. 1972, 43, 4536–4542

29.

Watson

P. K.

Electrostatic and hydrodynamic effects in the electrical breakdown of liquid dielectrics. IEEE Trans. Electl Insulation 1985, 20 (2), 395–399

30.

Dhanik

Joshi

S. S.

Modeling of a single resistance capacitance pulse discharge in micro-electro discharge machining. J. Mfg Sci. Engng 2005, 127, 759–767

31.

Nanostructured & Amorphous Materials, Inc(NanoAmor), available from http://www.nanoamor.com

32.

Masuzawa

Micro-EDM In Proceedings of the Thirteenth International Symposium on Electro-machining, Bilbao, Spain 2001, 3–19

33.

Amorim

F. L.

Weingaertner

W. L.

The influence of generator actuation mode and process parameters on the performance of finish EDM of tool steel. J. Mater. Process. Technol. 2005, 166, 411–416

34.

K. L.

Yan

H. H.

Huang

F. Y.

Chen

S. C.

Improvement of surface finish on SKD steel using electro-discharge machining with aluminum and surfactant added dielectric. Int. J. Mach. Tools Mf 2005, 45, 1195–1201

35.

Feng

J. Q.

Hays

D. A.

Relative importance of electrostatic forces on powder particles. Powder Technol. 2003, 135–136, 65–75

36.

Kansal

H. K.

Singh

Kumar

Technology and research developments in powder mixed electric discharge machining (PMEDM). J. Mater. Process. Technol. 2007, 184, 32–41

37.

Bleys

Kruth

J. P.

Lauwers

Schacht

Balasubramanian

Froyen

Humbeeck

J. V.

Surface and sub-surface quality of steel after EDM. Adv. Engng Mater. 2006, 8 (1–2), 15–25

38.

Blatnik

Valentincic

Junkar

Percentage of harmful discharges for surface current density monitoring in electrical discharge machining process. Proc IMechE, Part B: J. Engineering Manufacture, 221 (12), 1677–1684 DOI: 10.1243/09544054JEM816

39.

Marafona

Black layer characterisation and electrode wear ratio in electrical discharge machining (EDM). J. Mater. Process. Technol. 2007, 184, 27–31