Friction conditions at the tool-chip interface are one of the most important inputs for modelling and simulation of the machining process. However, the nature of the tool-chip contact is often assumed in developing finite element models, thereby seriously affecting their reliability. In this paper, results of an investigation into the tool-chip contact interface using uncoated tungsten-based cemented carbide tools in dry high-speed turning of AISI 1045 steel are presented. The tests were conducted at cutting speeds ranging between 198 and 879m/min with a feed rate of 0.1mm/rev and a constant depth of cut of 2.5 mm. The effects of cutting speed on tool rake face contact length, contact area, friction, element mapping, and surface roughness are studied and discussed. It is shown that the quantitative methods, used here to characterize the tool-chip contact region, can provide valuable data for accurate and reliable modelling of the metal machining process over a wide range of cutting speeds.
SaoubiR. M.ChandrasekaranH.Innovative methods for the investigation of tool-chip adhesion and layer formation during machiningAnn. CIRP, 2005, 54(1), 59–62.
4.
MativengaP. T.AbukhshimN. A.SheikhM. A.HonB. K. K.An investigation of tool-chip contact phenomena in high-speed turning using coated toolsProc. IMechE, Part B: J. Engineering Manufacture, 2006, 220, 657–667.
5.
AbukhshimN. A.MativengaP. T.SheikhM. A.An investigation of the tool-chip contact length and wear in high-speed turning of EN19 steelProc. Instn Mech. Engrs, Part B: J. Engineering Manufacture, 2004, 218, 889–903.
6.
SadikM. I.LindstromB.The role of tool-chip contact length in metal cuttingJ. Mater. Processing Technol., 1993, 37, 613–627.
7.
FriedmanM. Y.LenzE.Investigation of the tool-chip contact length in metal cuttingInt. J. Mach. Tools Des., 1970, 10, 401–416.
8.
ZorevN. N.Interrelationship between shear processes occurring along tool face and on shear plane in metal cutting. In Proceedings of the International Production Engineering Research Conference, Pittsburgh, Pennsylvania, USA, 1963, pp. 42–49 (ASME, New York).
9.
TrentE. M.Metal cutting, 1977, pp. 18–30 (Butterworth, Oxford).
10.
BowdenF. P.TaborD.The friction and lubrication of solids, 1954, pp. 53–88 (Oxford University Press, Oxford).
11.
ChildsT. H. C.Material porperties requirement in modelling metal machiningMachining Sci. Technol., 1998, 2(2), 303–306.
12.
RamanS.LongstreetA.GuhaD.A fractal view of tool-chip interfacial friction in machiningWear, 2002, 253, 1111–1120.
13.
ChildsT. H. C.DirikoluM. H.MaekawaK.Modelling of friction in the simulation of metal cutting. In Tribology for Energy Conservation, Proceedings of the 24th Leeds-Lyon Symposium on Tribology, London, September 1997, 1998, pp. 337–346 (Elsevier, Amsterdam).
14.
PerssonU.ChandrasekaranH.MerstallingerA.Adhesion between some tool and work materials in fretting and relation to metal cuttingWear, 2001, 249, 293–301.
15.
ConstableC. P.YarwoodJ.RobinsonG.LuoQ.LewisD. B.MünzW.-D.Investigation of wear processes on worn tools using Raman microscopySurf. Engng, 2002, 18, 127–132.
16.
GekondeH. O.SubramanianS. V.Tribology of tool-chip interface and tool wear mechanismsSurf. Coatings Technol., 2002, 149, 151–160.
17.
MillsB.HaoC. S.QiH. S.Formation of an adherent layer on a cutting tool studied by micromachining and finite element analysisWear, 1997, 208, 61–66.
18.
QiH. S.MillsB.Modelling of the dynamic tool-chip interface in metal cuttingJ. Mater. Processing Technol., 2003, 138, 201–207.
19.
AbukhshimN. A.MativengaP. T.SheikhM. A.Tool-chip contact phenomena for uncoated and coated carbides in high speed turning of high strength alloy steel. In Proceedings of the Fifth International Conference on High Speed Machining, Metz, France, 2006, pp. 1–10 (University of Metz, France).
20.
RechJ.Influence of cutting tool coatings on the tribological phenomena at the tool-chip interface in orthogonal turningSurf. Coatings Technol., 2006, 200, 5132–5139.
21.
DevillezA.LeskoS.MozercW.Cutting tool crater wear measurement with white light interferometryWear, 2004, 256(1–2), 56–65.
22.
ArsecularatneJ. A.KristyantoB.MathewP.An investigation of the high speed machining process using a variable flow stress machining theoryMachining Sci. Technol., 2004, 8(2), 211–233.
23.
SutterG.MolinariA.Analysis of the cutting force components and friction in high speed machiningTrans. ASME, J. Mfg Sci. Engng, 2005, 127, 245–250.
24.
MoufkiA.DevillezA.DudzenskiD.MolinariA.Thermomechanical modelling of cutting and experimental validation. In Metal cutting and high speed machining (Eds DudzinskiD.MolinariA.SchulzH.), 2002, pp. 51–68 (Kluwer, Dodrecht).
25.
KlockeF.HoppeS.Mechanisms of chip formation in high speed cutting. In Scientific fundamentals of high speed cutting (Ed. SchulzH.), 2001, pp. 1–11 (Carl Hanser Verlag, Munich).
26.
FinzerT.High speed milling of steel and cast iron. In High speed machining (Ed. SchulzH.), 1996, pp. 43–45 (Carl Hanser Verlag, Munich).
27.
AbukhshimN. A.MativengaP. T.SheikhM. A.Heat generation and temperature prediction in metal cutting: A review and implications for high speed machiningInt. J. Mach. Tools Mf., 2006, 46(7–8), 782–800.
MoufkiA.MolinariA.DudzenskiD.Modelling of orthogonal cutting with a temperature dependent friction lawJ. Mechanics Physics Solids, 1998, 46(10), 2103–2138.
30.
McClainB.BatzerS.MaldonadoG. I.A numeric investigation of rake face stress distribution in orthogonal machiningJ. Mater. Processing Technol., 2002, 123, 114–119.
31.
XieL.-J.SchmidtJ.SchmidtC.BiesingerF.2D FEM estimate of tool wear in turning operationWear, 2005, 258, 1479–1490.
32.
SartkulvanichV.AltanT.Effects of flow stress and friction models in finite element simulation of orthogonal cutting - a sensitivity studyMachining Sci. Technol., 2005, 9, 1–25.
33.
GrzesikW.Determination of temperature distribution in the cutting zone using hybrid analytical-FEM techniqueInt. J. Mach. Tools Mf., 2006, 46(6), 651–658.
34.
KlockeF.RaedtH.-W.HoppeS.2D-FEM simulation of the orthogonal high speed cutting processMachining Sci. Technol., 2001, 5(3), 323–340.
35.
GrzesikW.The influence of thin hard coatings on frictional behaviour in the orthogonal cutting processTribology Int., 2000, 33(2), 131–140.
36.
BarrowG.A review of experimental and theoretical techniques for assessing cutting temperaturesAnn. CIRP, 1973, 22(2), 203–211.
