Percentage of harmful discharges for surface current density monitoring in electrical discharge machining process

Abstract

Electrical discharge machining (EDM) is performed in the gap between the workpiece (usually the anode) and the electrode (usually the cathode). The gap is filled with a dielectric and the pulses generated by a special generator cause an electrical breakdown in the gap. A breakdown discharge occurs which removes material from the workpiece. The EDM process has been used for more than 50 years, but the influence of the surface current density on the process stability is not well understood. The surface current density is very important in the case of the machining of rough surfaces where the highest material removal rate (MRR) is preferred. For a given eroding surface there exists an optimal electrical current at which the highest MRR is achieved. It is reported in the literature that the percentage of the discharges that are harmful to the EDM process depends on the surface current density in the gap. Thus, experiments were performed to find out the possibility of using the percentage of harmful discharges to monitor the surface current density of the EDM process.

Keywords

spark erosion pulse discrimination surface current density rough machining machining surface process stability tool wear

References

Yan

B. H.

Wang

A. C.

Huang

C. Y.

Huang

F. Y.

Study of precision micro-holes in borosilicate glass using micro EDM combined with micro ultrasonic vibration machining

Int. J. Mach. Tools Mf, 2002, 42(10), 1105–1112.

Junkar

Valentinčič

Towards intelligent control of electrical discharge machining. In Proceedings of the Conference on Manufacturing systems, Aachen, 1999, pp. 453–457.

Valentinčič

A model of EDM process parameter selection upon the size of eroding surface. PhD Thesis (in Slovene), University of Ljubljana, Faculty of Mechanical Engineering, 2003.

Kyoshi

Feeder for electrical discharge machining. Patent JP 57 138 544 A, 1982.

Wollenberg

Shulze

H. P.

Goerish

Online determination of the working area on sinking EDM. EDM Technology, EDM Technology Transfer, 1996, 7–13.

Rajurkar

K. P.

Wang

W. M.

Zhao

W. S.

WEDM adaptive control for variable height components. Ann. CIRP, 1994, 199–202.

DiBitonto

D. D.

Eubank

P. T.

Patel

M. R.

Barrufet

M. A.

Theoretical models of the electrical discharge machining process. I. A simple cathode erosion model

J. Appl. Phys., 1989, 66(9), 4095–4103.

Crookall

J. R.

An analysis of EDM utilisation in industrial tooling manufacture

Ann. CIRP, 27(1), 1978, 113–118.

CIRP, Scientific technical committee E: Summary specifications of pulse analysers for spark-erosion machining, 1979.

10.

Tarng

Y. S.

Tseng

C. M.

Chung

L. K.

A fuzzy pulse discriminating system for electrical discharge machining

Int. J. Mach. Tools Mf, 1997, 37(4), 511–522.

11.

Garbajs

Statistical model for an adaptive control of EDM-process

Ann. CIRP, 34(1), 1985, 499–502.

12.

Dauw

D. F.

Advanced pulse discriminating system for EDM process analysis and control

Ann. CIRP, 32(1), 1983, 541–539.

13.

Weck

Dehmer

J. M.

Analysis and adaptive control of EDM sinking process using the ignition delay time and fall time as parameter

Ann. CIRP, 41(1), 1992, 243–246.

14.

Liao

Y. S.

Yan

M. T.

Chang

C. C.

A neural network approach for the online estimation of workpiece height in WEDM

J. Mater. Process. Technol., 121(2–3), 2002, 252–258.

15.

Blatnik

Percentage of the short circuit discharges for surface current density monitoring in EDM process. Diploma work, University of Ljubljana, 2004.