The dynamics and limits on the scaling of a flexible kinetic sculpture

Abstract

Highly flexible structures may be scaled up by different criteria that lead to different degrees of structural integrity as the scale increases. This paper first explores the effects of different scaling rules, focusing in particular on a double-size version of the Len Lye kinetic sculpture Blade, whose aesthetic performance characteristics must be preserved as the size is increased. Stresses in the sculpture increase, reaching first an economic limit beyond which frequent fatigue failure makes the sculpture too costly to operate. As the scale further increases, a size is reached where the sculpture will collapse. A dimensional parameter for comparing the values of the life to failure for different construction materials is also developed. The second part of the paper summarizes the results of different analytical approaches to the dynamics of Blade, both with and without the inclusion of an axial acceleration load due to gravity. The results of analyses are found to be in good agreement with experimental data. The paper closes by discussing some of the design implications of implementing the drive system for a double-size version of Blade that has been built and is now on public display.

Keywords

kinetic sculpture flexible structure dynamics dynamic scaling of structures

Get full access to this article

View all access options for this article.

References

Gooch

S. D.

Raine

J. K.

A twice full scale ‘Blade’—the engineering design of a kinetic sculpture. In Proceedings of the IPENZ Annual Conference, Wellington, New Zealand, 1997, Vol. 2, pp. 247–252.

Timoshenko

Gere

Theory of Elastic Stability, 1961 (McGraw-Hill, New York).

Naguleswaran

Vibration of a vertical cantilever with and without axial freedom at the clamped end. J. Sound Vibr., 1991, 146(2), 191–198.

Raine

J. K.

Gooch

S. D.

Universe and Blade: Dynamic analysis and engineering design of flexible kinetic sculptures. IPENZ Trans., November 1998, 25(1), 29–42.

Ashby

M. F.

Materials Selection in Mechanical Design, 1992 (Pergamon, Oxford).

Steidel

R. F.

An Introduction to Mechanical Vibrations, 1989 (John Wiley, New York).

Timoshenko

Vibration Problems in Engineering, 1928 (Van Nostrand, New York).

Leissa

A. W.

Vibration of Plates, NASA SP 160, 1969 (US Government Printing Office, Washington, DC).

Young

Vibration of rectangular plates by the Ritz method. J. Appl. Mechanics, 1950, 17, 448–453.

10.

Barton

M. V.

Vibration of rectangular and skew cantilever plates. J. Appl. Mechanics, 1951, 18, 129–134.

11.

Dickinson

S. M.

Di Blasio

On the use of orthogonal polynomials in the Rayleigh-Ritz method for the study of the flexural vibration and buckling of isotropic and orthotropic rectangular plates. J. Sound Vibr., 1986, 108(2), 51–62.

12.

Dickinson

S. M.

On the use of simply supported plate functions in the Rayleigh-Ritz method applied to the flexural vibration of rectangular plates. J. Sound Vibr., 1978, 59(1), 143–146.

13.

Bassily

S. F.

Dickinson

S. M.

On the use of beam functions for problems of plates involving free edges. J. Appl. Mechanics, 1975, 42, 858–864.

14.

Bhat

R. B.

Natural frequencies of rectangular plates using characteristic orthogonal polynomials in Rayleigh-Ritz method. J. Sound Vibr., 1985, 102, 493–499.

15.

Simons

D. A.

Leissa

A. W.

Vibrations of rectangular cantilever plates subjected to in-plane acceleration loads. J. Sound Vibr., 1971, 17(3), 407–422.

16.

Fauconneau

Laird

W. M.

Bounds for the natural frequencies of a simply supported beam carrying a uniformly distributed axial load. J. Mech. Engng. Sci., 1967, 9(2), 149–155.

17.

Burden

R. L.

Faires

J. D.

Reynolds

A. C.

Numerical Analysis, 2nd edition, 1981 (Prindle, Weber and Schmidt, Boston, Massachusetts).

18.

Bhat

R. B.

Vibration of rectangular plates using beam characteristic polynomials in the Rayleigh-Ritz method. In Proceedings of the Third International Modal Analysis Conference, Orlando, Florida, 1985, pp. 28–31.