An experimental and numerical study of the expansion forming of a thick-walled microgroove tube

Abstract

CO₂ refrigerant-based air conditioning and refrigeration (ACR) is an increasing concern in many industrial sectors for its zero ozone depletion potential. One of the major requirements in its application is the forming technology of thick-walled tube according to the extremely high pressure working conditions of the ACR system. This article presents a study on the expansion process joining the thick-walled microgroove copper tube to aluminium fins. Experiments of the forming process have been carried out. Finite-element models are developed to investigate the deformation of overall and local structures. Evaluation of the joining quality along the longitude axis of the tube is first attempted. The agreement of the results on the contact surface profile confirms that the joint is far away from full contact in the axial section. Formation mechanism of the unexpected contact status lies in displacement of the contact points along the section of the fin collar, which is mainly related to the expanding ratio. To improve the forming quality, discussion on processing parameters and die geometry is conducted. Results show that the expanding ratio is the major factor influencing the thermal—mechanical performance of the joint and 2–6 per cent can be the comprehensively beneficial range for a thick-walled ACR tube; average contact pressure can reach 1.76 Mpa under proper set. The results are helpful for improving the energy efficiency ratio performance of the natural refrigerant-based system.

Keywords

tube expansion thick-walled microgroove tube tube—fin joint

Get full access to this article

View all access options for this article.

References

Williams

D. K.

, ‘Comparison of residual stresses in the mechanical roll expansion of HX tubes into TEMA grooves’ Trans. ASME, J. Press. Vessel Technol. 129 (2007): 234–241.

Almeidaa

B. P. P.

Alvesb

M. L.

Rosaa

P. A. R.

Britoc

A. G.

Martins

P. A. F.

, ‘Expansion and reduction of thin-walled tubes using a die: Experimental and theoretical investigation’ Int. J. Mach. Tools Manuf. 46 (2006): 1643–1652.

Sukhawarn

, ‘Expander design in the tube expanding process’ J. Mech. Eng. Sci. 12 (1970): 30–36 DOI: 10.1243/JMES_JOUR_1970_012_006_02.

Chung

W. J.

Kim

J. L.

Song

T. J.

Kim

K. J.

Han

C. M.

, ‘Optimization of expanding velocity for a high-speed tube expander using a genetic algorithm with a neural network’ In Proceedings of the IASTED International Conference on Modeling, Simulation and Optimization, 2004, pp. 111–116.

Yokell

, ‘Expanded, and welded-and-expanded tube-to-tube sheet joints’ J. Press. Vessel Technol. 114 (1992): 157–165.

Bariani

Soavi

, ‘Contact pressure distribution in circular tube expansion using a conical plug’ Int. J. Mech. Sci. 24 (1982): 407–424.

Andy

, ‘Carbon dioxide — new uses for an old refrigerant’ Int. J. Refrig. 28 (2005): 1140–1148.

Wang

R. Z.

, ‘Perspectives for natural working fluids in China’ Int. J. Refrig. 30 (2007): 568–581.

Pettersent

Hafner

Skaugen

, ‘Development of compact heat exchangers for CO2 air-conditioning systems’ Int. J. Refrig. 21 (1998): 180–193.

10.

Hongsheng

Jiangping

Zhijiu

, ‘Experimental investigation of a CO2 automotive air conditioner’ Int. J. Refrig. 28 (2005): 1293–1301.

11.

Friedrich

, ‘Determination of the optimum high pressure for transcritical CO2-refrigeration cycles’ Int. J. Therm. Sci. 38 (1999): 325–330.

12.

Jin

M. C.

Min

S. K.

, ‘Experimental studies on the evaporative heat transfer and pressure drop of CO2 in smooth and micro-fin tubes of the diameters of 5 and 9.52 mm’ Int. J. Refrig. 30 (2007): 986–994.

13.

Yinghong

Ding

Dayong

, ‘Study on the influence of mandrel type on copper tube rotary draw bending’ Int. J. Mater. Prod. Technol., accepted.

14.

Guangliang

Shihong

Bing

Haiqu

, ‘Analysis on folding defects of inner grooved copper tubes during ball spin forming’ J. Mater. Process. Technol. 184 (2007): 393–400.

15.

Jin

Chang

N. K.

Baek

, ‘A study on the thermal contact conductance in fin—tube heat exchangers with 7 mm tube’ Int. J. Heat Mass Transf. 49 (2006): 1547–1555.

16.

Yovanovich

M. M.

Horton

T. E.

Ed., ‘Thermal contact correlations’ Spacecraft radiative transfer and temperature control: progress in aeronautics and astronautics (New York: AIAA 1982): 83–95.

17.

Sridhar

M. R.

Yovanovich

M. M.

, ‘Review of elastic and plastic contact conductance models: Comparison with experiment’ J. Thermophys. Heat Transf. 8 (1994): 633–40.

18.

Lambert

M. A.

Fletcher

L. S.

, ‘Review of models for thermal contact conductance of metals’ J. Thermophys. Heat Transf. 11 (1997): 129–40.

19.

Chaaban

Bazergui

, ‘Tube-tubesheet joint: A proposed equation the equivalent sleeve diameter used in the single-tube model’ ASME, J. Press. Vessel Technol. 114 (1992): 19–22.

20.

Qunfeng

Dayong

Yinghong

Xiaoqin

, ‘Experimental and numerical study of warm deep drawing of AZ31magnesium alloy sheet’ Int. J. Mach. Tools Manuf. 47 (2007): 436–443.