Static and dynamic pressure profiles of a patellar-tendon-bearing (PTB) socket

Abstract

The purpose of this study was to evaluate the pressure distribution at the stump/socket interface in amputees wearing the patellar-tendon-bearing socket. A specially built strain gauged type pressure transducer was used for measuring this pressure distribution in four unilateral transtibial amputees. Pressure and gait parameters were measured simultaneously while they were standing and walking. Pressure profiles were compiled at 10, 25 and 50 per cent of gait cycle and compared with the pressure profiles predicted by Radcliffe in 1961. The subject's anterior-posterior pressure profiles were different from each other. However, at toe-off, each subject exhibited an increase in pressure at the patellar tendon. Their medial-lateral pressure profiles were similar: exhibiting high pressure at the medial proximal and lateral distal regions except for one subject who exhibited high pressure at the lateral proximal region instead. The subjects' pressure profiles did not resemble Radcliffe's anticipated pressure profiles. This was because ground reaction force was not the only factor affecting the resulting pressure profiles.

Keywords

transtibial amputees patellar-tendon-bearing socket stump pressure biomechanics

Get full access to this article

View all access options for this article.

References

Radcliffe

C. W.

The biomechanics of below-knee prosthesis in normal, level, bipedal walking. Artif. Limbs, 1961, 6 (2), 16–24.

Radcliffe

C. W.

Foort

The patellar-tendon-bearing below-knee prosthesis. Biomechanics Laboratory report, University of California, Berkeley, California, 1961.

Sonck

W. A.

Cockrell

J. L.

Koepke

G. H.

Effect of liner material on interface pressures in below-knee prostheses. Arch. Phys. Medicine Rehabil., 1970, 51, 666–669.

Pearson

J. R.

Holmgren

March

Oberg

Pressures in critical regions of the below-knee patellartendon-bearing prosthesis. Bull. Prosthetic Res., 1973, 10 (19) Spring, 52–76.

Sanders

J. E.

Lam

Dralle

A. J.

Okumura

Interface pressures and shear stresses at thirteen socket sites on two persons with transtibial amputation. J. Rehabil. Res. Dev., 1997, 34 (1), 19–43.

Sanders

J. E.

Zachariah

S. G.

Baker

A. B.

Greve

J. M.

Clinton

Effects of changes in cadence, prosthetic componentry and time on interface pressure and shear stresses of three transtibial amputees. Clin. Biomech., 2000, 15, 684–694.

Zhang

Turner-Smith

A. R.

Tanner

Roberts

V. C.

Clinical investigation of the pressure and shear stress on the transtibial stump with prosthesis. Med. Engng Physics, 1998, 20, 188–198.

Lee

V. S. P.

Solomonidis

S. E.

Spence

W. D.

Stump-socket interface pressure as an aid to socket design in prostheses for transfemoral amputees—a preliminary study. Proc. Instn Mech. Engrs, Part H, Journal of Engineering in Medicine, 1997, 211, Part H, 167–180.

Kapp

Cummings

Prosthetic management. In Atlas Of Limb Prosthetics: Surgical, Prosthetics And Rehabilitation Principles (Eds Bowker

J. H.

Michael

J. W.

), 2nd edition, 1992, pp. 454–479 (Mosby Year Book, American Academy of Prosthetics and Orthotics, USA, St Louis).

10.

Fergason

Smith

D. G. S.

Socket consideration for the patient with a transtibial amputation. Clin. Orthop. Related Res., 1999, 361, 76–84.

11.

Convery

Buis

A. W. P.

Conventional patellar-tendon-bearing (PTB) socket/stump interface dynamic pressure distributions recorded during the prosthetic stance phase of gait of a transtibial amputee. Prosthetic Orthotics Int., 1998, 22, 193–198.