Modelling windage power loss from an enclosed spur gear

Abstract

Within a gearbox the majority of transmission losses can be attributed to bearing losses, meshing losses, or losses due to windage/churning. In this paper the commercial computational fluid dynamics (CFD) code Fluent 6.2.16 is applied in a two-dimensional study of windage power loss (WPL) from a single spur gear rotating in air. By comparing CFD data to published experimental data appropriate grid density and modelling parameters are identified. The model is used to investigate how peripheral shrouding affects WPL and whether WPL can be reduced through minor modifications to tooth tip geometry.

Non-dimensional shroud spacings (ratio of gap to gear PCD) of between 0.005 and 0.05 were investigated at shaft speeds between 5000 and 20 000 r/min. Although CFD data compared reasonably well to experimental data, trends were not reproduced and an optimum shroud could not be identified. A full three-dimensional study is recommended.

Modifying the tooth tip by adding a small chamfer on the leading edge reduced WPL by ∼6 per cent. A small fillet increased total WPL by a similar amount suggesting that WPL may increase as a gear wears. This preliminary study suggests further work in this area would be beneficial.

Keywords

spur gear power loss windage computational modelling computational fluid dynamics

Get full access to this article

View all access options for this article.

References

Weiss

Hirt

Efficiency Improvements for high speed gears. International Conference on Gears, Munich, Germany, 2002, vol. 2. pp. 1161–1174.

Lord

A. A.

An experimental investigation of geometric and oil flow effects on gear windage and meshing losses. PhD Thesis, University of Wales, Swansea, 1998.

Dawson

P. H.

Windage loss in larger high-speed gears. Proc. Instn Mech. Engrs, Part A: J. Power and Process Engineering, 1984, 198 (1), 51–59.

Dawson

P. H.

High speed gear windage. GEC Rev., 1988, 4 (3), 164–167.

Winfree

D. D.

Reducing gear windage losses from high speed gears. In Proceedings of DETC'00, ASME Power transmission and gearing conference, Baltimore Maryland, 10–13 September 2000, pp. 747–756.

Barnes

J. P.

Non-dimensional characterization of gear geometry, mesh loss and windage. Fall AGMA/ASME Meeting, San Diego, CA, 1997, 97FTM11, p 12.

Townsend

D. P.

Dudley's gear handbook, 2nd edition, 1991, section 12.5.2. (McGraw-Hill, NY, USA).

Dudley

D. W.

Gear handbook. The design, manufacture and application of gears, 1962, pp. 14–21 (McGraw-Hill, New York).

Heingartner

Mba

Determining power losses in the helical gear mesh; case study. DETC'03, ASME 2003 Design Engineering Technical Conferences and Computers and Information in Engineering Conference, Chicago, Illinois, 2003, vol. 4B, pp. 965–970.

10.

Anderson

N. E.

Loewenthal

S. H.

Efficiency of non-standard and high contact ratio involute spur gears. J. Mech. Transm. Auto. Design, 1986, 108, 118–126.

11.

Handschuh

R. F.

Kilmain

C. J.

Preliminary comparison of experimental and analytical efficiency results of high-speed helical gear trains. DETC'03, ASME 2003 Design Engineering Technical Conferences and Computers and Information in Engineering Conference, Chicago, Illinois, 2003, vol. 4B, pp. 949–955.

12.

Diab

Ville

Changenet

Velex

Windage losses in high speed gears - preliminary experimental and theoretical results. DETC'03, ASME 2003 Design Engineering Technical Conferences and Computers and Information in Engineering Conference, Chicago, Illinois, 2003, vol. 4B, pp. 941–947.

13.

Diab

Ville

Velex

Wendling

Simulations and experimental investigations on windage losses in high-speed gears. International Conference on Gears, Munich, Germany, 2005, pp. 1435–1450.

14.

Lee

C. W.

Air and oil flow investigations in an aeroengine bearing chamber. PhD Thesis, University of Nottingham chapter 6, 2004.

15.

Launder

B. E.

Spalding

D. B.

Lectures in mathematical models of turbulence, 1972 (Academic Press, London, England).

16.

Choudhury

Introduction to the renormalization group method and turbulence modeling. Fluent Inc. Technical Memorandum TM-107, 1993.

17.

Launder

B. E.

Reece

G. J.

Rodi

Progress in the development of a Reynolds-stress turbulence closure. J. Fluid Mech., 1975, 68, 537–566.

18.

Kader

Temperature and concentration profiles in fully turbulent boundary layers. Int. J. Heat Mass Transf., 1993, 24 (9), 1541–1544.

19.

Bilgen

Boulos

Functional dependence of torque coefficient of coaxial cylinder on gap width and Reynolds number. J. Fluids Eng., 1973, 1, 122–126.