A detailed literature survey is presented herein in order to overview the aerodynamic impact of non-radial blade stacking techniques applied to axial flow fan and compressor rotors. The literature suggests a consensus that forward blade sweep and skew provides a means for the following advantages in the part load operational range of low-speed axial flow turbofan and compressor rotors: improvement of efficiency and performance, and extension of stall-free operating range. However, the published research results are rather diversified regarding the judgment of performance and loss modifying effects of sweep and skew at the design point. The current paper summarizes the major aerodynamic phenomena related to such blade stacking techniques, in order to contribute to a general reasoning of performance and efficiency modification at the design flow rate. Furthermore, it provides guidelines how to consider these phenomena in tailoring the blade geometry for potential efficiency gain and for achievement of the prescribed total pressure rise at the design point. The role of adequate computational fluid dynamics tools was considered in the paper to be essential in evaluation of aerodynamic effects of non-radial blade stacking, as well as in incorporation of sweep and skew in systematic blade design techniques.
ClemenC.StarkU.Compressor blades with sweep and dihedral: a parameter study. In Proceedings of the 5th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, Prague, 2003, pp. 151–161.
2.
GallimoreS. J.BolgerJ. J.CumpstyN. A.TaylorM. J.WrightP. I.PlaceJ. M. M.The use of sweep and dihedral in multistage axial flow compressor blading - parts I and II. ASME J. Turbomach., 2002, 124, 521–541.
3.
CorsiniA.RispoliF.Using sweep to extend the stall-free operational range in axial fan rotors. Proc. Instn Mech. Engrs, Part A: J. Power and Energy, 2004, 218, 129–139.
4.
BeilerM. G.CarolusT. H.Computation and measurement of the flow in axial flow fans with skewed blades. ASME J. Turbomach., 1999, 121, 59–66.
5.
YamaguchiN.TominagaT.HattoriS.MitsuhashiT.Secondary-loss reduction by forward-skewing of axial compressor rotor blading. In Yokohama International Gas Turbine Congress, Yokohama, 1991, pp. II.61–II.68.
6.
GümmerV.SwobodaM.GollerM.DobatA.The impact of rotor tip sweep on the three-dimensional flow in a highly-loaded single-stage low-speed axial compressor: part I - design and numerical analysis. In Proceedings of the 5th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, Prague, 2003, pp. 163–174.
7.
RohkammH.WulffD.KosynaG.SaathoffH.StarkU.GümmerV.SwobodaM.GollerM.The impact of rotor tip sweep on the three-dimensional flow in a highly-loaded single-stage low-speed axial compressor: part II - test facility and experimental results. In Proceedings of the 5th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, Prague, 2003, pp. 175–185.
8.
McNultyG. S.DeckerJ. J.BeacherB. F.KhalidS. A.The impact of forward swept rotors on tip-limited low-speed axial compressors. ASME paper no. GT2003–38837, 2003.
9.
ClemenC.GümmerV.GollerM.RohkammH.StarkU.SaathoffH.Tip-aerodynamics of forward-swept rotor blades in a highly-loaded single-stage axial-flow low-speed compressor. In Proceedings of the 10th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery (ISROMAC10), Honolulu, 2004, paper no. 027.
10.
GollerM.GümmerV.ClemenC.SwobodaM.Enhancement of highly-loaded axial compressor stage performance using rotor blade tip tailoring, part I - numerical design studies. In Proceedings of the 6th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, Lille, 2005, pp. 88–99.
11.
RohkammH.KosynaG.SaathoffH.StarkU.Enhancement of highly-loaded axial compressor stage performance using rotor blade tip tailoring, part II - experimental results. In Proceedings of the 6th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, Lille, 2005, pp. 100–110.
12.
MohammedK. P.Prithvi RajD.Investigation on axial flow fan impellers with forward swept blades. ASME J. Fluids Eng., 1977, 543–547.
13.
CorsiniA.RispoliF.The role of forward sweep in subsonic axial fan rotor aerodynamics at design and off-design operating conditions. ASME paper no. GT2003–38671, 2003.
14.
BrownN. A.The use of skewed blades for ship propellers and truck fans. In Noise and Fluids Engineering. Winter Annual Meeting of ASME, Atlanta, 1977, pp. 201–207.
15.
WrightT.SimmonsW. E.Blade sweep for low-speed axial fans. ASME J. Turbomach., 1990, 112, pp. 151–158.
16.
MeixnerH. U.Vergleichende LDA-Messungen an unge-sichelten und gesichelten Axialventilatoren. Dissertation Universität Karlsruhe, VDI-Verlag, Reihe 7: Strömungstechnik, No. 266, Düsseldorf, 1995.
17.
BeilerM. G.Untersuchung der dreidimensionalen Strömung durch Axialventilatoren mit gekrümmten Schaufeln. Doctoral Dissertation, Universität-GH-Siegen, VDI Verlag Düsseldorf, Reihe 7: Strömungstechnik, Nr. 298, 1996.
18.
United States Patent.High efficiency and low weight axial flow fan. US Pat. no. 6 368 061 B1, 2002.
19.
LeeG. H.BaekJ. H.MyungH. J.Structure of tip leakage flow in a forward-swept axial-flow fan. Flow Turbul. Combust., 2003, 70, 241–265.
20.
WadiaA. R.SzucsP. N.CrallD. W.Inner workings of aerodynamic sweep. ASME J. Turbomach., 1998, 120, 671–682.
21.
VadJ.KwedikhaA. R. A.JabergH.Influence of blade sweep on the energetic behavior of axial flow turbomachinery rotors at design flow rate. ASME paper no. GT2004–53544, 2004.
22.
VadJ.KwedikhaA. R. A.JabergH.Effects of blade sweep on the performance characteristics of axial flow turbomachinery rotors. Proc. IMechE, Part A: J. Power and Energy, 2006, 220, 737–751.
23.
VadJ.KwedikhaA. R. A.HorváthCs.BalczóM.LohászM. M.RégertT.Aerodynamic effects of forward blade skew in axial flow rotors of controlled vortex design. Proc. IMechE, Part A: J. Power and Energy, 2007, 221, 1011–1023.
24.
KuhnK.Experimentelle Untersuchung einer Axialpumpe und Rohrturbine mit gepfeilten Schaufeln. PhD Thesis, Technische Universität Graz, Institut for Hydraulische Strömungsmaschinen, 2000.
25.
HelmingK.Numerical analysis of sweep effects in shrouded propfan rotors. J. Propuls. Power, 1996, 12, 139–145.
26.
DeichM. E.TroyanovskiiB. M.FilippovG. A.An effective way of improving the efficiency of turbine stages. Therm. Eng., 1990, 37, 520–523.
27.
Li.Y.QuangH.DuZ.-H.Optimization design and experimental study of low-pressure axial fan with forward-skewed blades. Int. J. Rotat. Mach., 2007, 2007, 10, Article ID 85275, doi: 10.1155/2007/85275.
28.
JangC.-M.SamadA.KimK-Y.Optimal design of swept, leaned and skewed blades in a transonic axial compressor. ASME paper no. GT2006–90384, 2006.
29.
SasakiT.BreugelmansF.Comparison of sweep and dihedral effects on compressor cascade performance. ASME J. Turbomach., 1998, 120, 454–464.
30.
SongY.ZhaoG.ChenF.WangZ.Experimental study of sweep and dihedral effects on compressor cascade performance. In Proceedings of the 6th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, Lille, 2005, pp. 1–9.
31.
Van Den BraembusscheR. A.VadJ.Challenges in optimisation of axial flow turbomachinery blades for three-dimensional flow, including sweep and dihedral effects. In Modelling fluid flow, 2004, pp. 99–103 (Springer Verlag, Heidelberg).
32.
HorlockJ. H.DentonJ. D.A review of some early design practice using computational fluid dynamics and a current perspective. ASME J. Turbomach., 2005, 127, 5–13.
33.
LakshminarayanaB.Fluid dynamics and heat transfer of turbomachinery, 1996 (John Wiley & Sons, Inc., New York).
34.
CarolusT.Ventilatoren, 2003 (Teubner Verlag).
35.
GovardhanM.Krishna KumarO. G.SitaramN.Computational study of the effect of sweep on the performance and flow field in an axial flow compressor rotor. Proc. IMechE, Part A: J. Power and Energy, 2007, 221, 315–329.
36.
ForstnerM.KuhnK.GlasW.JabergH.The flow field of pump impellers with forward and backward sweep. In Proceedings of the 4th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, Florence, 2001, pp. 577–587.
37.
ForstnerM.Experimentelle Untersuchungen an vorwärts und rückwärts gepfeilten Axialpumpenschaufeln. PhD Thesis, Technische Universität Graz, Institut for Hydraulische Strömungsmaschinen, 2002.
38.
GlasW.Optimierung gepfeilter Pumpenschaufeln mit Evolutionären Algorithmen. PhD Thesis, Technische Universität Graz, Institut for Hydraulische Strömungsmaschinen, 2000.
39.
SmithL. M.YehH.Sweep and dihedral effects in axial-flow turbomachinery. ASME J. Basic Eng., 1963, 85, 401–416.
40.
LewisR. I.HillJ. M.The influence of sweep and dihedral in turbomachinery blade rows. J. Mech. Eng. Sci., 1971, 13, 266–285.
41.
PullanG.HarveyN. W.Influence of sweep on axial flow turbine aerodynamics at midspan. ASME J. Turbomach., 2007, 129, 591–598.
42.
DentonJ. D.XuL.The exploitation of three-dimensional flow in turbomachinery design. In Turbomachinery design systems, lecture series 1999–02, 1999 (Von Karman Institute for Fluid Dynamics, Belgium).
43.
PlaceJ. M. M.CumpstyN. A. Discussion in reference [29], 1998.
44.
DomercqO.EscuretJ.-F.Tip clearance effect on high-pressure compressor stage matching. Proc. IMechE, Part A: J. Power and Energy, 2007, 221, 759–767.
45.
KhalidS. A.KhalsaA. S.WaitzI. A.TanC. S.GreitzerE. M.CumpstyN. A.AdamczykJ. J.MarbleF. E.Endwall blockage in axial compressors. ASME J. Turbomach., 1999, 121, 499–509.
46.
FriedrichsJ.BaumgartenS.KosynaG.StarkU.Effect of stator design on stator boundary layer flow in a highly loaded single-stage axial-flow low-speed compressor. ASME J. Turbomach., 2001, 123, 483–489.
47.
VadJ.BenczeF.Three-dimensional flow in axial flow fans of non-free vortex design. Int. J. Heat Fluid Flow, 1998, 19, 601–607.
48.
VadJ.Effects of sweep and spanwise changing circulation applied to airfoils: A case study. J. Comput. Appl. Mech., 2004, 5, 383–400.
49.
VadJ.Analytical modeling of radial fluid migration in the boundary layer of axial flow turbomachinery blades. ASME paper no. GT2006–90523, 2006.
50.
GoltzI.KosynaG.WulffD.SchrappH.BrossS.Part load operating performance and stall inception of a single-stage axial-flow pump. In Proceedings of the 10th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery (ISROMAC10), Honolulu, 2004, paper no. 014.
51.
BiolloR.BeniniE.Systematic investigation on swept and leaned transonic compressor rotor blades. In Proceedings of the 7th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, Athens, 2007, pp. 205–214.
52.
MoreauS.HennerM.BrouckaertJ. F.NealD.Numerical and experimental investigation of rotor-stator interaction in automotive engine cooling fan systems. In Proceedings of the 7th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, Athens, 2007, pp. 215–228.
53.
CorsiniA.RispoliF.SheardA. G.Development of improved blade tip endplate concepts for low-noise operation in industrial fans. Proc. IMechE, Part A: J. Power and Energy, 2007, 221, 669–681.
54.
Van den BraembusscheR. A.Modern turbomachinery component design. In Proceedings of the Conference on Modelling Fluid Flow (CMFF'06), Budapest, 2006, pp. 33–48.
55.
GlasW.JabergH.Multi-objective evolutionary algorithm for the optimization of swept pump impellers. In Proceedings of the 4th European Conference on Turbomachinery Fluid Dynamics and Thermodynamics, Florence, 2001, pp. 469–479.
