Running-in effect on the load-carrying capacity of a water-lubricated SiC thrust bearing

Abstract

It is known the friction of self-mated SiC in water strongly depends on the roughness of their contact surfaces, and a proper running-in process is the way to obtain low friction by smoothing the contact surfaces of SiC with tribochemical wear. In this paper, the running-in process of surface-contacted SiC (thrust-bearing-type contact) in water is studied experimentally. It is found the maximum running-in load has a large influence on the load-carrying capacity, which is measured as the critical load for the transition from hydrodynamic to mixed lubrication in this research. A multi-step loading running-in method is proposed to increase the load-carrying capacity of SiC thrust bearings working in water. Finally, the running-in process of a laser textured SiC surface is studied, the effect of the pore area ratio on the roughness of the run-in surface is reported, and the mechanism of the effect of micropores is discussed.

Keywords

running-in SiC load-carrying capacity water lubrication surface texture

Get full access to this article

View all access options for this article.

References

Nau

B. S.

Mechancal seal face materials

Proc. Instn Mech. Engrs, Part J: J. Engineering Tribology, 1987, 211, 165–183.

Asanabe

Applications of ceramics for tribological components

Tribology Int., 1987, 20 (6), 355–364.

Andersson

Lintula

Load-carrying capability of water-lubricated ceramic journal bearings

Tribology Int., 1994, 27 (5), 315–321.

Tomizawa

Fischer

T. E.

Friction and wear of silicon nitride and silicon carbide in water: Hydrodyn-amic lubrication at low sliding speed obtained by tribochemical wear

ASLE Trans., 1987, 30 (1), 41–46.

Sasaki

The effects of water on friction and wear of ceramics

J. Japan Soc. Lubric. Engrs, 1988, 33 (8), 620–628.

Andersson

Juhanko

Nikkila

A. P.

Lintula

Influence of topography on the running-in of water-lubricated silicon carbide journal bearings

Wear, 1996, 201 (1-2), 1–9.

Andersson

Nikkila

A. P.

Lintula

Wear characteristics of water-Lubricated SiC journal bearings in intermittent motion

Wear, 1994, 179 (1-2), 57–62.

Wong

H. C.

Umehara

Kato

The effect of surface roughness on friction of ceramics sliding in water

Wear, 1998, 218 (2), 237–243.

Hsu

S. M.

Shen

M. C.

Ceramic wear maps

Wear, 1996, 200, 154–175.

10.

Kato

Hirayama

The transition of wear mode during the running-in process of silicon nitride sliding in water

Wear, 1997, 205, 55–63.

11.

Chen

Kato

Adachi

The comparisons of sliding speed and normal load effect on friction coefficients of self-mated Si₃N₄ and SiC under water lubrication

Tribology Int., 2002, 35, 129–135.

12.

Chen

Kato

Adachi

Friction and wear of self-mated SiC and Si₃N₄ sliding in water

Wear, 2001, 250, 246–255.

13.

Wang

Kato

Adachi

Aizawa

The effect of laser texturing of SiC surface on the critical load for the transition of water lubrication mode from hydrodynamic to mixed

Tribology Int., 2001, 34, 703–711.

14.

Wang

Kato

Adachi

The lubrication effect of micro-pits on parallel sliding faces of SiC in water

Tribology Trans., 2002, 45 (3), 294–301.

15.

Lebeck

A. O.

Parallel sliding load support in the mixed friction regime. 1: The experimental data

Trans. ASME, J. Tribology, 1987, 109 (1), 189–195.