Effects of debris particles in sliding/rolling elastohydrodynamic contacts

Abstract

A theoretical simulation of the behaviour of debris particles in elastohydrodynamic (EHD) contacts is an effective means for obtaining information regarding the life and performance of lubricated machine elements compared with costly experimentation. The present work indicates that debris particles are often responsible for two failure modes: (a) scuffing caused by particle agglomeration in the inlet zone of an EHD contact and (b) local melting due to high heat produced by the friction of debris in sliding contacts. The present predictions are in agreement with experimental evidence in two ways: firstly, in that EHD contacts may fail because of scuffing if the lubricant becomes contaminated, where the failure due to inlet blockage by debris and eventually fluid starvation, and, secondly, in that sliding asperity contacts encounter high flash temperatures which may cause local melting and thus plastic deformations.

Keywords

debris particles scuffing flash temperatures elastohydrodynamic (EHD) contacts

Get full access to this article

View all access options for this article.

References

Sayles

R. S.

Loannides

Debris damage in rolling bearings and its effects on fatigue life

Trans. ASME, J. Lubric. Technol., 1988, 110, 26–31.

Hamer

J. C.

Sayles

R. S.

Loannides

Particle deformation and counterface damage when relatively soft particles are squashed between hard anvils

STLE Tribology Trans., 1989, 32 (3), 281–288.

Sayles

R. S.

Hamer

J. C.

Loannides

The effects of pariculate contamination in rolling bearings—a state of the art review

Proc. Instn Mech. Engrs, Part G, Journal of Aerospace Engineering, 1990, 204 (G1), 29–36.

Dwyer-Joyce

R. S.

The effect of lubricant contamination on rolling bearing performance. PhD thesis, Tribology Section, Mechanical Engineering Department, Imperial College of Science, Technology and Medicine, London, 1992.

Hamrock

B. J.

Fundamentals of Fluid Film Lubrication, 1994 (McGraw-Hill, New York).

Wan

G. T.Y.

Spikes

H. A.

The behavior of suspended solid particles in rolling and sliding elastohydrodynamic contacts

STLE Trans., 1987, 31 (1), 12–21.

Cameron

The Principles of Lubrication, 1966 (Longman, London).

Carslaw

H. S.

Jaeger

J. C.

Conduction of Heat in Solids, reprint, 1993 (Clarendon, Oxford).

Blok

Theoretical study of temperature rise at surfaces of actual contact under oilness lubricating conditions (General discussion on lubrication)

Proc. Instn Mech. Engrs, 1937, 2, 222–235.

10.

Jaeger

J. C.

Moving sources of heat and the temperature at sliding contacts

Proc. R. Soc. (Lond.), 1942, 76, 203–224.

11.

Love

A. E. H.

A Treatise on the Mathematical Theory of Elasticity, 4th edition, 1944 (Dover Publications, New York).

12.

Goodier

J. N.

On the integration of the thermo-elastic equations

Phil Mag., 1937, 23 (7), 1017–1032.

13.

Nicolson

D. M.

Scuffing at high temperature and speed, PhD thesis, Mechanical Engineering Department, Tribology Section, Imperial College of Science, Technology and Medicine, London, 1996.

14.

Griffioen

J. A.

Bair

Winer

W. O.

Infrared surface temperature measurements in a sliding ceramic—ceramic contact. In

Mechanisms and Surface Distress, Proceedings of the 11th Leeds—Lyon Symposium on Tribology, 1984, pp. 238–245 (Elsevier, Amsterdam).

15.

Wolf

The influence of surface roughness texture on the temperature and scuffing in sliding contact

Wear, 1991, 143, 99–118.

16.

Enthoven

J. C.

Spikes

H. A.

Visual observation of the process of scuffing.

In Proceedings of the 21st Leeds-Lyon Symposium on Tribology, Leeds, 1994, pp. 487–494 (Elsevier, Amsterdam).

17.

Chandrasekaran

Khemchandari

M. V.

Sharma

J.P.

Effect of abrasive contaminants on scuffing

Tribology Int., 1985, 18 (4), 219–222.