Observations on and the modelling of erosive wear of a long-radius pneumatic conveyor bend

Abstract

This paper describes the results of an experimental investigation of the erosive wear, and puncture, of a long-radius bend in a pneumatic conveyor when used to convey abrasive particles. Measurements were taken of (a) the local air pressure in the pipe bore (used to obtain values of the local superficial air velocity), (b) the mass of abrasive particles flowing through the pipe with time, (c) the reduction in the thickness of the bend wall and (d) the particle concentration distribution using a simple optical obscuration technique.

From analysis of the results it was deduced that an accumulation of the particles against the outside bend wall, and the shape of the pipe bore itself, caused the particles to rebound back towards the pipe bore centre-line after primary impact. This behaviour caused an intensification of particle impacts in the region where secondary impacts predominate, and this is where puncture was found to occur.

A simple empirical model is proposed for the prediction of the bend wear life. This is based upon an analogy between the particle dynamics in the bend and the optical aberration of a cylindrical mirror of similar dimensions to the pipe bore.

Keywords

erosion wear particle impact pneumatic conveyor pipe model

Get full access to this article

View all access options for this article.

References

Mills

Erosive wear problems in industry with particular reference to process plant, power stations and bulk handling systems. Workshop Notes, Presented at the SOLIDEX 86 Conference and Exhibition, Harrogate, June 1986.

Burnett

A. J.

The use of laboratory erosion tests for the prediction of wear in pneumatic conveyor bends. PhD thesis, University of Greenwich, London, 1996.

Humphrey

J. A. C.

Fundamentals of fluid motion in erosion by solid particle impact

Int. J. Heat Mass Transfer, 1990, 11 (3), 170–195.

Clift

Grace

J. R.

Weber

M. E.

Bubbles, Drops and Particles, 1978 (Academic Press, New York).

Burnett

A. J.

De Silva

S. R.

Reed

A. R.

Comparisons between ‘sand blast’ and ‘centripetal effect accelerator’ erosion testers

Wear, 1995, 186-187, 168–178.

Burnett

A. J.

Bingley

M. S.

Bradley

M. S. A.

An investigation of the low velocity/low concentration solid particle erosion of a structural mild steel using a centripetal erosion tester. In Proceedings of the Fifth International Conference on

Bulk Materials Storage, Handling and Transportation, University of Newcastle, New South Wales, Australia, 1995, pp. 191–198 (Institution of Engineers, Barton, ACT, Australia).

Shirazi

S. A.

Shadley

J. R.

McLaury

B. S.

Rybicki

E. F.

A procedure to predict solid particle erosion in elbows and tees

Trans. ASME, J. Pressure Vessel Technol., 1995, 117, 45–52.

Sato

Shimizu

Yokomine

Numerical prediction of erosion for suspension duct flow

Wear, 1995, 186-187, 203–209.

Shimizu

Yagi

Yoshida

Yokomine

Erosion of gaseous suspension flow duct due to particle collision (I): Experimental determination of erosion rate by individual collision

Nucl. Sci. Technol., 1993, 30, 881–889.

10.

Selves

T. P.

Analysis and control of splitting ratios of particulate materials at bifurcations in pneumatic conveying pipelines. PhD thesis, University of Greenwich, London, 1995.

11.

BS 1042: Part 2A: 1973 Pilot Tubes, 2A, Class A Accuracy, 1973 (British Standards Institution, London).

12.

Bradley

M. S.A.

Reed

A. R.

An improved method of predicting pressure drop along pneumatic conveying pipelines

Powder Handling Processing, 1990, 2 (3), 223–227.

13.

Yan

Mass flow measurement of bulk solids in pneumatic pipelines

Measmt Sci. Technol., 1996, 7, 1687–1706.

14.

Woodhead

S. R.

The measurement of particle velocity and suspension density in pneumatic coal injection systems. PhD thesis, University of Greenwich, London, 1992.

15.

Soo

S. L.

Regalbuto

J. A.

Concentration distribution in two-phase pipe flow

Can. J. Chem. Engng, October 1960, 160–166.

16.

Tsuji

Morikawa

Tanaka

Nakatsukasa

Nakatani

Numerical simulation of gas-solid two-phase flow in a two-dimensional horizontal channel

Int. J. Multiphase Flow, 1987, 13 (5), 671–684.

17.

Tsuji

Shen

N. Y.

Morikawa

Lagrangian simulation of dilute gas-solid flows in a horizontal pipe

Adv. Powder Technol., 1991, 2 (1), 63–81.

18.

Oesterle

Petitjean

Simulation of particle-to-particle interactions in gas-solid flows

Int. J. Multiphase Flow, 1993, 19 (1), 199–211.

19.

Huber

Sommerfeld

Characterisation of the cross-sectional particle concentration distribution in pneumatic conveying systems

Powder Technol., 1994, 79, 191–210.

20.

Anand

Hovis

S. K.

Conrad

Scattergood

R. O.

Flux effects in solid particle erosion

Wear, 1987, 118, 243–257.

21.

Andrews

D. R.

Horsfield

Particle collisions in the vicinity of an eroding surface

J. Phys. D: Appl. Phys., 1983, 16, 525–538.

22.

Burnett

A. J.

Famish

R. J.

Reed

A. R.

Modelling of the particle dynamics in a rotating disc accelerator erosion tester. In IMechE World Tribology Congress on Tribology, London, 1997, poster paper (Mechanical Engineering Publications, London).