Porous sunshade roof cover sheet is a new structure used for heat insulation on building roofs. This paper describes a wind tunnel study that investigated the effects of various parapets on wind loading on porous sunshade roof cover sheets for a low-rise building. The test model (200 mm high (H), 470 mm wide (B), 710 mm deep (D)) at a length scale of 1:50 had sixteen porous sunshade roof cover sheets on the roof, four of which were equipped with pressure taps. Wind pressures were measured simultaneously at many pressure taps on both the upper and lower surfaces of the porous sunshade roof cover sheets. Perimeter parapets (solid parapet, porous parapet and wind spoiler) of different heights were used to investigate their effects on wind loading on porous sunshade roof cover sheets through results of wind pressure coefficients, wind force coefficients, cross-correlation coefficients between upper and lower surface pressures, and probability density functions.
AmanoT.FujiK. and TazakiS. (1988). “Wind loads on permeable roof-blocks in roof insulation systems”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 29, No. 1–3, pp. 39–48.
2.
AIJ-RFLB (2004). AIJ Recommendations for Loads on Buildings, Architectural Institute of Japan.
3.
ASCE 7–05 (2006). Minimum Design Loads for Buildings and Other Structures, American Society of Civil Engineers, Reston, Virginia, USA.
BanksD. (2000). The Suction Induced by Conical Vortices on Low-Rise Buildings with Flat Roofs, PhD Thesis, Department of Civil Engineering, Colorado State University, Fort Collins, Colorado.
6.
BienkiewiczB. and SunY. (1992a). “Wind-tunnel study of wind loading on loose-laid roofing systems”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 43, No. 1–3, pp. 1817–1828.
7.
BienkiewiczB. and SunY. (1992b). “Local wind loading on the roof of a low-rise building”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 45, No. 1, pp. 11–24.
8.
BienkiewiczB. and SunY. (1997). “Wind loading and resistance of loose-laid roof paver systems”, Journal of Wind Engineering and Industrial Aerodynamic, Vol. 72, pp. 401–410.
9.
CheungJ.C.K. and MelbourneW.H. (1988). “Wind loading on a porous roof”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 29, No. 1–3, pp. 19–28.
10.
ChinoN.IwasaY.MatakiY.HagiwaraT. and SatoH. (1991). “Internal pressure of double composite exteriors”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 38, No. 2–3, pp. 381–391.
11.
EN 1991-1-4 (2005). Eurocode 1: Actions on Structures, Part 1–4: General Actions- Wind actions, European Standard, Brussels, Belgium.
12.
GerhardtH.J. and KramerC. (1983). “Wind loads on wind-permeable building facades”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 11, No. 1–3, pp. 1–20.
13.
KareemA. and LuP.C. (1992). “Pressure fluctuations on flat roofs with parapets”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 43, No. 1–3, pp. 1775–1786.
14.
KindR.J. and WardlawR.L. (1982). “Failure mechanisms of loose-laid roof-insulation systems”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 9, No. 3, pp. 325–341.
15.
KindR.J. (1988). “Worst suctions near edges of flat rooftops with parapets”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 31, No. 2–3, pp. 251–264.
16.
KoppG.A.SurryD. and MansC. (2005a). “Wind effects of parapets on low buildings: Part 1. Basic aerodynamics and local loads”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 93, No. 11, pp. 817–841.
17.
KoppG.A.MansC. and SurryD. (2005b). “Wind effects of parapets on low buildings: Part 2. Structural loads”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 93, No. 11, pp. 843–855.
18.
KoppG.A.MansC. and SurryD. (2005c). “Wind effects of parapets on low buildings: Part 4. Mitigation of corner loads with alternative geometries”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 93, No. 11, pp. 873–888.
19.
KramerC.GerhardtH.J. and KusterH.W. (1979). “On the wind-loading mechanisms of roofing elements”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 4, No. 3–4, pp. 415–427.
20.
LytheG. and SurryD. (1983). “Wind loading of flat roofs with and without parapets”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 11, No. 1–3, pp. 75–94.
21.
MansC.KoppG.A. and SurryD. (2005). “Wind effects of parapets on low buildings: Part 3. Parapet loads”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 93, No. 11, pp. 857–872.
22.
PindadoS. and MeseguerJ. (2003). “Wind tunnel study on the influence of different parapets on the roof pressure distribution of low-rise buildings”, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 91, No. 9, pp. 1133–1139.
23.
StathopoulosT. and BaskaranA. (1987). “Wind pressures on flat roofs with parapets”, Journal of Structural Division, ASCE, Vol. 113, No. 12, pp. 2166–2180.
24.
WuF. (2000). Full-Scale Study of Conical Vortices and their Effects Near Corners, PhD Thesis, Department of Civil Engineering, Texas Tech University, Lubbock, Texas.
