Design Fatigue Load of Sign Support Structures Due to Truck-Induced Wind Gust

Abstract

This research presents a universal approach for determining the design fatigue load due to truck-induced wind gust for highway overhead sign support structures. The fatigue load is determined on the basis of the dynamic properties of the structure. It is applicable to structures in which the dynamic response can be approximated by a single-degree-of-freedom system. Typical examples include cantilever- and bridge-type overhead sign support structures. The developed approach incorporates these parameters in a simplified systematic procedure that can be readily used by engineers. Principles relating to mechanical vibration and utilization of the shock response spectrum were used to determine the load. The fatigue load is selected from the shock response spectrum in terms of the natural frequency of the structure and the speed of the truck. Comparisons were made with the current truck-induced gust fatigue design provisions given in the 2009 AASHTO Standard Specifications for Structural Supports for Highway Signs, Luminaires, and Traffic Signals. Additional comparisons were made with dynamic finite element analysis of a modeled support structure.

Get full access to this article

View all access options for this article.

References

Fouad

F. H.

, Calvert

E. A.

, and Nunez

NCHRP Report 411: Structural Supports for Highway Signs, Luminaires, and Traffic Signals. TRB, National Research Council, Washington, D.C., 1998.

Standard Specifications for Structural Supports for Highway Signs, Luminaires, and Traffic Signals, 5th ed. AASHTO, Washington, D.C., 2009.

Kaczinski

M. R.

, Dexter

R. J.

, and Van Dien

J. P.

NCHRP Report 412: Fatigue-Resistant Design of Cantilevered Signal, Sign, and Light Supports. TRB, National Research Council, Washington, D.C., 1998.

DeSantis

P. V.

, and Haig

P. E.

Unanticipated Loading Causes Highway Sign Failure. Proc. ANSYS Conference, 1996.

Dexter

R. J.

, and Ricker

M. J.

NCHRP Report 469: Fatigue-Resistant Design of Cantilevered Signal, Sign, and Light Supports. Transportation Research Board of the National Academies, Washington, D.C., 2002.

Cook

R. A.

, Bloomquist

, Agosta

A. M.

, and Taylor

K. F.

Wind Load Data for Variable Message Signs. Report FL/DOT/RMS/0728–9488. Engineering and Industrial Experiment Station, University of Florida, Gainesville, 1996.

Creamer

B. M.

, Frank

K. H.

, and Klingner

R. E.

Fatigue Loading on Cantilever Sign Support Structures From Truck Wind Gusts. Research Report 209-1F. Texas State Department of Highways and Public Transportation, Austin, April, 1979.

Edwards

J. A.

, and Bingham

W. L.

Deflection Criteria for Wind Induced Vibrations in Cantilever Highway Sign Structures. Report FHWA/NC/84-001. Center for Transportation Engineering Studies, North Carolina State University, Raleigh, 1984.

Ginal

Fatigue Performance of Full-Span Sign Support Structures Considering Truck-Induced Gust and Natural Wind Pressures. MS thesis. Marquette University, Milwaukee, Wisc., Dec. 2003.

10.

Harris

C. M.

Shock and Vibration Handbook, 4th ed. McGraw-Hill Companies, Inc., New York, 1996.

11.

Foutch

D. A.

, Kim

T. W.

, LaFave

J. M.

, and Rice

J. A.

Evaluation of Aluminum Highway Sign Truss Designs and Standards for Wind and Truck Gust Loadings. Research Report Number 153. Illinois Department of Transportation, Springfield, Dec. 2006.

12.

Irvine

An Introduction to the Shock Response Spectrum. Vibrationdata Publications, Madison, Ala., May 24, 2002. www.vibrationdata.com.