Slab Upwarping of Twin-Block Slab Track on Subgrade

Abstract

This study is a preliminary analysis of the causes of upwarping of reinforced concrete slabs of a twin-block slab track, specifically on the subgrade–bridge transition section. The analysis considers the structural features and force characteristics of slab track on the basis of site investigations and numerical simulation, and a corresponding repair method is proposed. It is determined that the temperature and temperature gradient of the slab, the connection status between the slab and the hydraulically bonded layer (HBL), and the position of the terminal spine are the main factors that lead to the upwarping of the slab. Model tests on the force transmission parameters between slab and HBL are carried out to measure the adhesive strength of the cohesive contact and the friction coefficient for the frictional contact. The adhesive strength is found to range from 0.803 to 1.57 MPa. The actual friction coefficient with large dispersion varies significantly from 1.5 to 3.0 because of the influence of the strength of the material and the friction roughness. The analysis output shows that the upwarping of the slab decreases with the reduction of temperature and temperature gradient of the slab, but the upwarping increases with the decrease in adhesive strength and friction coefficient. Increasing the number of terminal spines with 4-m spacing, which is optimized after the spacing effect, contributes to the reduction of the slab upwarping. A reasonable layout scheme for anchor pins can significantly improve the integrity and stability of track structure affected by slab upwarping. From the output of the analysis, a repair method that involves setting additional anchor pins between the slab and HBL is thus recommended.

Get full access to this article

View all access options for this article.

References

Zhao

Ballastless Track Structure for High-Speed Railway. China Railway Publishing House, Beijing, 2006.

Ren

, Xiang

, and Liu

Force Characteristics of Longitudinally Coupled Slab Track Turnout on Bridges Under Temperature Action. In Transportation Research Record: Journal of the Transportation Research Board, No. 2159, Transportation Research Board of the National Academies, Washington, D.C., 2010, pp. 85–90.

Wang

, Ren

, Xiang

, and Liu

Influence of Rub-Plate Length on Forces and Displacements of Longitudinally Coupled Slab Track for a Bridge Turnout. Proceedings of the Institution of Mechanical Engineers Part F: Journal of Rail and Rapid Transit, Vol. 226, No. F3, 2012, pp. 284–293.

Bachmann

, Mohr

, and Kowalski

The Rheda 2000 Ballastless Track System. European Railway Review, Vol. 8, No. 1, 2003, pp. 44–51.

Freudenstein

Rheda 2000: The Ballastless Track System for HighSpeed Rail Traffic of Rail One. Railway Track Review, Vol. 46, 2006, pp. 47–51.

Georgios

Slab Track Systems for High-Speed Railways. MA thesis. Royal Institute of Technology, Sweden, 2012.

Design of the CRTS II Twin-Block Ballastless Track on West of Zheng Passenger Line. Railway Construction Technology, No. 4, 2010.

Zhang

, Zhang

, and Zhao

Structure Analysis and Size Optimization of the End Beam on Wuhan-Guang Passenger Dedicated Line. Subgrade Engineering, Vol. 148, No. 1, 2010, pp. 31–33.

Liu

, Zhao

, Yang

, and Wang

Design Theory and Method of Ballastless Track of Passenger Dedicated Railways. Southwest Jiaotong University Press, Chengdu, China, 2010.

10.

Fourth Survey and Design Institute of China Railway. General Reference Design Drawing of High-Speed Railway CRTS I Twin-Block Ballastless Track. Research Institute of Economic Planning of the Ministry, China, 2011.

11.

Investigation Report of Current Chinese Slab Track Operation. Southwest Jiaotong University, Chengdu, China, 2011.

Slab Upwarping of Twin-Block Slab Track on Subgrade–Bridge Transition Section

Abstract

Get full access to this article

References