Journal of Dental Research

Indirect composites have been undergoing an impressive evolution over the last few years. Specifically, recent developments in computer-aided design–computer-aided manufacturing (CAD-CAM) blocks have been associated with new polymerization modes, innovative microstructures, and different compositions. All these recent breakthroughs have introduced important gaps among the properties of the different materials. This critical state-of-the-art review analyzes the strengths and weaknesses of the different varieties of CAD-CAM composite materials, especially as compared with direct and artisanal indirect composites. Indeed, new polymerization modes used for CAD-CAM blocks—especially high temperature (HT) and, most of all, high temperature–high pressure (HT-HP)—are shown to significantly increase the degree of conversion in comparison with light-cured composites. Industrial processes also allow for the augmentation of the filler content and for the realization of more homogeneous structures with fewer flaws. In addition, due to their increased degree of conversion and their different monomer composition, some CAD-CAM blocks are more advantageous in terms of toxicity and monomer release. Finally, materials with a polymer-infiltrated ceramic network (PICN) microstructure exhibit higher flexural strength and a more favorable elasticity modulus than materials with a dispersed filler microstructure. Consequently, some high-performance composite CAD-CAM blocks—particularly experimental PICNs—can now rival glass-ceramics, such as lithium-disilicate glass-ceramics, for use as bonded partial restorations and crowns on natural teeth and implants. Being able to be manufactured in very low thicknesses, they offer the possibility of developing innovative minimally invasive treatment strategies, such as “no prep” treatment of worn dentition. Current issues are related to the study of bonding and wear properties of the different varieties of CAD-CAM composites. There is also a crucial need to conduct clinical studies. Last, manufacturers should provide more complete information regarding their product polymerization process, microstructure, and composition, which significantly influence CAD-CAM material properties.

It is well known that the service life of contemporary composite restoration is unsatisfactory, and longevity of dentin bonding is one of the major culprits. Bonding is essentially a hybridization process in which dental substrate and adhesive resin interact with each other through an exchange process. Thus, the longevity of dentin bonding can only be improved with enhanced qualities in substrate, adhesive resin, and their interaction within the hybridization zone. This review aims to collect and summarize recent advances in utilizing nonthermal atmospheric plasmas (NTAPs)—a novel technology that delivers highly reactive species in a gaseous medium at or below physiologic temperature—to improve the durability of dentin bonding by addressing these 3 issues simultaneously. Overall, NTAP has demonstrated efficacies in improving a number of critical properties for dentin bonding, including deactivation of oral pathogens, modification of surface chemistry/properties, resin polymerization, improvement in adhesive-dentin interactions, and establishment of auxiliary bonding mechanism. While a few preliminary studies have indicated the benefit of NTAP to bond strength and stability, additional researches are warranted to employ knowledge acquired so far and to evaluate these properties in a systematic way.

The aim of this systematic review and meta-analysis was to study the effectiveness of psychological interventions in adults and adolescents with poor oral health. The review follows the PRISMA guidelines for systematic reviews. The PICO format (population, intervention, comparison, and outcome) was used to define eligible studies. The populations were adults or adolescents (≥13 y of age and independent of others) with poor oral health (defined as dental caries, periodontal disease, and/or peri-implantitis). The interventions were psychological and/or behavioral models and theories, in comparison with traditional oral health education/information. The primary outcomes were dental caries, periodontitis, gingivitis, and peri-implantitis. Secondary outcomes were dental plaque, oral health–related behavior, health-related quality of life, health beliefs and attitudes, self-perceived oral health, and complications/risks. The systematic literature search identified 846 articles in December 2013 and 378 articles in July 2015. In total, 11 articles on 9 randomized controlled trials were found to meet the inclusion criteria. These reported on adults with periodontal disease, and several used motivational interviewing (MI) as their mode of intervention. The CONSORT guidelines and the GRADE approach were used for study appraisal and rating of evidence. The meta-analysis showed no statistically significant differences in gingivitis or plaque presence. In addition, a meta-analysis on MI compared with education/information found no statistically significant differences in gingivitis presence. Only 1 meta-analysis—on psychological interventions versus education/information regarding the plaque index—showed a small but statistically significant difference. There were also statistically significant differences reported in favor of psychological interventions in oral health behavior and self-efficacy in toothbrushing. However, the clinical relevance of these differences is difficult to estimate. The certainty of evidence was low. Future research needs to address several methodological issues and not only study adults with periodontal disease but also adolescents and patients with dental caries and peri-implantitis.

The objective of the study was to estimate the prevalence of periodontitis at state and local levels across the United States by using a novel, small area estimation (SAE) method. Extended multilevel regression and poststratification analyses were used to estimate the prevalence of periodontitis among adults aged 30 to 79 y at state, county, congressional district, and census tract levels by using periodontal data from the National Health and Nutrition Examination Survey (NHANES) 2009–2012, population counts from the 2010 US census, and smoking status estimates from the Behavioral Risk Factor Surveillance System in 2012. The SAE method used age, race, gender, smoking, and poverty variables to estimate the prevalence of periodontitis as defined by the Centers for Disease Control and Prevention/American Academy of Periodontology case definitions at the census block levels and aggregated to larger administrative and geographic areas of interest. Model-based SAEs were validated against national estimates directly from NHANES 2009–2012. Estimated prevalence of periodontitis ranged from 37.7% in Utah to 52.8% in New Mexico among the states (mean, 45.1%; median, 44.9%) and from 33.7% to 68% among counties (mean, 46.6%; median, 45.9%). Severe periodontitis ranged from 7.27% in New Hampshire to 10.26% in Louisiana among the states (mean, 8.9%; median, 8.8%) and from 5.2% to 17.9% among counties (mean, 9.2%; median, 8.8%). Overall, the predicted prevalence of periodontitis was highest for southeastern and southwestern states and for geographic areas in the Southeast along the Mississippi Delta, as well as along the US and Mexico border. Aggregated model-based SAEs were consistent with national prevalence estimates from NHANES 2009–2012. This study is the first-ever estimation of periodontitis prevalence at state and local levels in the United States, and this modeling approach complements public health surveillance efforts to identify areas with a high burden of periodontitis.

Biological mediators have been used to enhance periodontal regeneration. The aim of this prospective randomized controlled study was to evaluate the safety and effectiveness of 3 doses of fibroblast growth factor 2 (FGF-2) when combined with a β-tricalcium phosphate (β-TCP) scaffold carrier placed in vertical infrabony periodontal defects in adult patients. In this double-blinded, dose-verification, externally monitored clinical study, 88 patients who required surgical intervention to treat a qualifying infrabony periodontal defect were randomized to 1 of 4 treatment groups—β-TCP alone (control) and 0.1% recombinant human FGF-2 (rh-FGF-2), 0.3% rh-FGF-2, and 0.4% rh-FGF-2 with β-TCP—following scaling and root planing of the tooth prior to a surgical appointment. Flap surgery was performed with EDTA conditioning of the root prior to device implantation. There were no statistically significant differences in patient demographics and baseline characteristics among the 4 treatment groups. When a composite outcome of gain in clinical attachment of 1.5 mm was used with a linear bone growth of 2.5 mm, a dose response pattern detected a plateau in the 0.3% and 0.4% rh-FGF-2/β-TCP groups with significant improvements over control and 0.1% rh-FGF-2/β-TCP groups. The success rate at 6 mo was 71% in the 2 higher-concentration groups, as compared with 45% in the control and lowest treatment groups. Percentage bone fill in the 2 higher-concentration groups was 75% and 71%, compared with 63% and 61% in the control and lowest treatment group. No increases in specific antibody to rh-FGF-2 were detected, and no serious adverse events related to the products were reported. The results from this multicenter trial demonstrated that the treatment of infrabony vertical periodontal defects can be enhanced with the addition of rh-FGF-2/β-TCP (ClinicalTrials.gov NCT01728844).

Proximal caries infiltration has been shown to be efficacious in hampering caries lesion progression when performed by dentists working in a university setting. The aim of this randomized split-mouth, placebo-controlled clinical trial was to assess the efficacy of resin infiltration of proximal caries lesions being performed by several dentists in private practices, in combination with individualized oral hygiene plus noninvasive measures compared with these alone. In this study, 87 children and young adults (with 238 pairs of proximal caries lesions radiographically extending into the inner half of the enamel [E2] or the outer third of the dentin [D1]) were randomly allocated to either 1 of 2 treatments. Test lesions were infiltrated, and a mock treatment was performed in control lesions by 5 German private practitioners. All patients received instructions for a noncariogenic diet, flossing and fluoridation, and individualized noninvasive interventions. The primary outcome was radiographic lesion progression (pairwise comparison) evaluated independently by 2 evaluators who were blinded to treatment allocation. After approximately 10 mo (mean ± SD 307 ± 43 d), 92 of 148 lesion pairs in 24 of 38 treated patients who were at high caries risk could be re-evaluated clinically as well as radiographically using individualized bitewing holders, as at baseline; 186 of 204 lesion pairs in 70 of 77 patients (35 of 38 high-risk patients) could be evaluated after 18 mo (mean 542 ± 110 d). No unwanted effects were observed. After 10 mo, progression was recorded in 2 of 92 test lesions (2%) and in 22 of 92 control lesions (24%) (P = 0.001, McNemar/Obuchowski test; relative risk reduction, 91; 95% confidence interval, 62%–98%). After 18 mo, lesion progression was recorded in all included patients in 10 of 186 test lesions (5%) and in 58 of 186 control lesions (31%) (P < 0.001; relative risk reduction, 83; 95% confidence interval, 67%–91%). Thus, resin infiltration seems to be more efficacious in reducing lesion progression compared with individualized noninvasive measures alone over a period of 18 mo when performed in a private practice setting by various practitioners (German Clinical Trials Register / Deutsches Register Klinischer Studien DRKS00009963).

The differential diagnosis of dental wear lesions affects their clinical management. We hypothesized that surface texture parameters can differentiate simulated erosion, abrasion, and erosion-abrasion lesions on human enamel and dentin. This in vitro study comprised 2 parts (both factorial 4 × 2), with 4 lesion types (erosion, abrasion, erosion-abrasion, and sound [no lesion; control]) and 2 substrates (enamel and dentin). Flattened/polished dental specimens were used in part 1, whereas natural dental surfaces were used in part 2. Testing surfaces were evaluated in blind conditions, using average surface roughness (Sa) and the following scale-sensitive fractal analysis parameters: area-scale fractal complexity (Asfc), exact proportion length-scale anisotropy of relief (eplsar), scale of maximum complexity (Smc), and textural fill volume (Tfv). Two-way analyses of variance, followed by Fisher’s protected least significant difference tests (α = 0.05), were used to evaluate the effects of lesion and substrate. Classification trees were constructed to verify the strength of potential associations of the tested parameters. In part 1, Asfc, Sa, and Tfv were able to differentiate erosion and erosion-abrasion lesions from the sound (no lesion) control in both substrates; only Asfc differentiated erosion and erosion-abrasion enamel lesions (all P < 0.05). The best association of parameters correctly classified up to 84% and 94% of the lesions on enamel and dentin, respectively. In part 2, only Asfc differentiated erosion and erosion-abrasion lesions from the sound (no lesion) control in both substrates, whereas eplsar was able to differentiate erosion from erosion-abrasion (all P < 0.05). The association of parameters correctly classified up to 81% and 91% of the lesions in enamel and dentin, respectively. Asfc, Sa, and Tfv were able to differentiate erosion and erosion-abrasion lesions, despite their complicated surface textures. The association of parameters improved the differentiation of lesions for both enamel and dentin in polished or natural surfaces.

The purpose of this study was to investigate the relationship between hygroscopic expansion and polymerization shrinkage for compensation of polymerization shrinkage stresses in a restored tooth. One resin-modified glass-ionomer (RMGI) (Ketac Nano, 3M ESPE), 2 compomers (Dyract, Dentsply; Compoglass, Ivoclar), and a universal resin-based composite (Esthet•X HD, Dentsply) were tested. Volumetric change after polymerization (“total shrinkage”) and during 4 wk of water storage at 37°C was measured using an optical method (n = 10). Post-gel shrinkage was measured during polymerization using a strain gauge method (n = 10). Extracted human molars with large mesio-occluso-distal slot preparations were restored with the tested restorative materials. Tooth surfaces at baseline (preparation), after restoration, and during 4 wk of 37°C water storage were scanned with an optical scanner to determine cuspal flexure (n = 8). Occlusal interface integrity was measured using dye penetration. Data were analyzed using analysis of variance and post hoc tests (significance level 0.05). All tested materials shrunk after polymerization. RMGI had the highest total shrinkage (4.65%) but lowest post-gel shrinkage (0.35%). Shrinkage values dropped significantly during storage in water but had not completely compensated polymerization shrinkage after 4 wk. All restored teeth initially exhibited inward (negative) cuspal flexure due to polymerization shrinkage. Cuspal flexure with the RMGI restoration was significantly less (–6.4 µm) than with the other materials (−12.1 to −14.1 µm). After 1 d, cuspal flexure reversed to +5.0 µm cuspal expansion with the RMGI and increased to +9.3 µm at 4 wk. After 4 wk, hygroscopic expansion compensated cuspal flexure in a compomer (Compoglass) and reduced flexure with Dyract and resin-based composite. Marginal integrity (93.7% intact restoration wall) was best for the Compoglass restorations and lowest (73.1%) for the RMGI restorations. Hygroscopic expansion was more effective in compensating shrinkage stress than would be assumed based on total shrinkage, because only post-gel shrinkage needed compensation. Effective expansion is therefore hygroscopic expansion minus post-gel shrinkage.

Enamel demineralization adjacent to pit and fissure sealants leads to the formation of marginal caries, which can necessitate the replacement of existing sealants. Dental materials with bioactive glass, which releases ions that inhibit dental caries, have been studied. The purpose of this study was to evaluate the enamel surface adjacent to sealants containing 45S5 bioactive glass (BAG) under simulated microleakage between the material and the tooth in a cariogenic environment. Sealants containing 45S5BAG filler were prepared as follows: 0% 45S5BAG + 50.0% glass (BAG0 group), 12.5% 45S5BAG + 37.5% glass (BAG12.5 group), 25.0% 45S5BAG + 25.0% glass (BAG25.0 group), 37.5% 45S5BAG + 12.5% glass (BAG37.5 group), and 50.0% 45S5BAG + 0% glass (BAG50.0 group). A cured sealant disk was placed over a flat bovine enamel disk, separated by a 60-µm gap, and immersed in lactic acid solution (pH 4.0) at 37 °C for 15, 30, and 45 d. After the storage period, each enamel disk was separated from the cured sealant disk, and the enamel surface was examined with optical 3-dimensional surface profilometer, microhardness tester, and scanning electron microscopy. The results showed a significant increase in roughness and a decrease in microhardness of the enamel surface as the proportion of 45S5BAG decreased (P < 0.05). In the scanning electron microscopy images, enamel surfaces with BAG50.0 showed a smooth surface, similar to those in the control group with distilled water, even after prolonged acid storage. Additionally, an etched pattern was observed on the surface of the demineralized enamel with a decreasing proportion of 45S5BAG. Increasing the 45S5BAG filler contents of the sealants had a significant impact in preventing the demineralization of the enamel surface within microgaps between the material and the tooth when exposed to a cariogenic environment. Therefore, despite some marginal leakage, these novel sealants may be effective preventive dental materials for inhibiting secondary caries at the margins.

Surface nanofeatures and bioactive ion chemical modification are centrally important in current titanium (Ti) oral implants for enhancing osseointegration. However, it is unclear whether the addition of bioactive ions definitively enhances the osteogenic capacity of a nanostructured Ti implant. We systematically investigated the osteogenesis process of human multipotent adipose stem cells triggered by bioactive ions in the nanostructured Ti implant surface. Here, we report that bioactive ion surface modification (calcium [Ca] or strontium [Sr]) and resultant ion release significantly increase osteogenic activity of the nanofeatured Ti surface. We for the first time demonstrate that ion modification actively induces focal adhesion development and expression of critical adhesion–related genes (vinculin, talin, and RHOA) of human multipotent adipose stem cells, resulting in enhanced osteogenic differentiation on the nanofeatured Ti surface. It is also suggested that fibronectin adsorption may have only a weak effect on early cellular events of mesenchymal stem cells (MSCs) at least in the case of the nanostructured Ti implant surface incorporating Sr. Moreover, results indicate that Sr overrides the effect of Ca and other important surface factors (i.e., surface area and wettability) in the osteogenesis function of various MSCs (derived from human adipose, bone marrow, and murine bone marrow). In addition, surface engineering of nanostructured Ti implants using Sr ions is expected to exert additional beneficial effects on implant bone healing through the proper balancing of the allocation of MSCs between adipogenesis and osteogenesis. This work provides insight into the future surface design of Ti dental implants using surface bioactive ion chemistry and nanotopography.

The aim of this in vitro study was to evaluate the early cell response and protein adsorption elicited by the argon plasma treatment of different commercially available titanium surfaces via a chair-side device. Sterile disks made of grade 4 titanium (n = 450, 4-mm diameter) with 3 surface topographies (machined, plasma sprayed, and zirconia blasted and acid etched) were allocated to receive 4 testing treatments (2% and 10% protein adsorption and cell adhesion with MC3T3-E1 and MG-63). Furthermore, the specimens were divided to undergo 1) argon plasma treatment (10 W, 1 bar for 12 min) in a plasma reactor, 2) ultraviolet (UV) light treatment for 2 h (positive control group), or 3) no treatment (control group). Pretreatment surface analyses based on a scanning electron microscope and profilometer images were also performed. Profilometric analysis demonstrated that the evaluated specimens perfectly suit the standard parameters. The use of argon plasma was capable of affecting the quantity of proteins adsorbed on the different surfaces, notwithstanding their roughness or topographic features at a low fetal bovine serum concentration (2%). UV light treatment for 2 h attained similar results. Moreover, both the plasma of argon and the UV light demonstrated a significant increase in the number of osteoblasts adherent at 10 min in all tested surfaces. Within its limitations, this in vitro study highlights the potential biological benefits of treating implant surfaces with plasma of argon or UV, irrespective of the roughness of the titanium surface. However, in vivo experiments are needed to confirm these preliminary data and settle the rationale of a treatment that might be clinically relevant in case of bone-reparative deficiencies.

Multiphoton confocal microscopy and nonlinear spectroscopy are used to investigate the caries process in dentin. Although dentin is a major calcified tissue of the teeth, its organic phase comprises type I collagen fibers. Caries drive dentin demineralization and collagen denaturation. Multiphoton microscopy is a powerful imaging technique: the biological materials are transparent to infrared frequencies and can be excited to penetration depths inaccessible to 1-photon confocal microscopy. The laser excitation greatly reduces photodamage to the sole focal region, and the signal-to-noise ratio is improved significantly. The method has been used to follow pathologic processes involving collagen fibrosis or collagen destruction based on their 2-photon excited fluorescence (2PEF) emission and second harmonic generation (SHG). Combining multiphoton imaging with nonlinear spectroscopy, we demonstrate that both 2PEF and SHG intensity of human dentin are strongly modified during the tooth caries process, and we show that the ratio between SHG and 2PEF signals is a reliable parameter to follow dental caries. The ratio of the SHG/2PEF signals measured by nonlinear optical spectroscopy provides valuable information on the caries process, specifically on the degradation of the organic matrix of dentin. The goal is to bring these nonlinear optical signals to clinical application for caries diagnosis.

Enamel is an acellular material formed by the intricate process of amelogenesis. Disruption caused at the initial stages of development, by means of mutations in the ENAM gene encoding the enamelin protein, results in enamel hypoplasia. Little is known about the consequence of ENAM mutation on the enamel structure at a crystallographic level. The aim of this study was to characterize the structure of ENAM-mutated enamel to develop a deeper understanding of the role of enamelin protein during formation with regard to crystal organization. Synchrotron X-ray microdiffraction (SXRD) and scanning electron microscopy (SEM) have been used to measure and correlate enamel crystallography and microstructure in hypoplastic and healthy enamel. Rietveld refinement carried out on 2-dimensional diffraction patterns, collected from the Advanced Photon Source, were used to quantify changes in the preferred orientation (crystallographic texture) within the labial regions of each tooth slice and then correlated with the local microstructure. In general, healthy deciduous incisors displayed a higher degree of crystal organization across the labial surface in comparison with the hypoplastic enamel. ENAM plays the greatest functional role at the enamel-dentine junction (EDJ), as it was the region that exhibited lowest texture relative to unaffected controls. Other areas within the tooth, however, such as the cusp tip, displayed greater organization in line with healthy enamel, suggesting its effects are restricted to the early stages of enamel secretion. Observed clinically, the surface of ENAM-mutated hypoplastic enamel can appear to be normal, yet severe sub-nano and microstructural defects appear beneath the subsurface layer. Quantitative characterization of the crystallographic properties from enamel with known genotype expands the understanding of enamel formation processes and can aid better clinical diagnosis and tailor-made treatment.

Formation and growth of hydroxyapatite crystals during amelogenesis generate a large number of protons that must be neutralized, presumably by HCO₃⁻ ions transported from ameloblasts into the developing enamel matrix. Ameloblasts express a number of transporters and channels known to be involved in HCO₃⁻ transport in other epithelia. However, to date, there is no functional evidence for HCO₃⁻ transport in these cells. To address questions related to HCO₃⁻ export from ameloblasts, we have developed a polarized 2-dimensional culture system for HAT-7 cells, a rat cell line of ameloblast origin. HAT-7 cells were seeded onto Transwell permeable filters. Transepithelial resistance was measured as a function of time, and the expression of transporters and tight junction proteins was investigated by conventional and quantitative reverse transcription polymerase chain reaction. Intracellular pH regulation and HCO₃⁻ transport were assessed by microfluorometry. HAT-7 cells formed epithelial layers with measureable transepithelial resistance on Transwell permeable supports and expressed claudin-1, claudin-4, and claudin-8—key proteins for tight junction formation. Transport proteins previously described in maturation ameloblasts were also present in HAT-7 cells. Microfluorometry showed that the HAT-7 cells were polarized with a high apical membrane CO₂ permeability and vigorous basolateral HCO₃⁻ uptake, which was sensitive to Na⁺ withdrawal, to the carbonic anhydrase inhibitor acetazolamide and to H₂DIDS inhibition. Measurements of transepithelial HCO₃⁻ transport showed a marked increase in response to Ca²⁺- and cAMP-mobilizing stimuli. Collectively, 2-dimensional HAT-7 cell cultures on permeable supports 1) form tight junctions, 2) express typical tight junction proteins and electrolyte transporters, 3) are functionally polarized, and 4) can accumulate HCO₃⁻ ions from the basolateral side and secrete them at the apical membrane. These studies provide evidence for a regulated, vectorial, basolateral-to-apical bicarbonate transport in polarized HAT-7 cells. We therefore propose that the HAT-7 cell line is a useful functional model for studying electrolyte transport by ameloblasts.