Journal of Industrial Textiles

In this study, composite nanofibers from a solution of polyacrylonitrile (PAN), functionalized multi-walled carbon nanotubes (f-MWCNTs), and silver nitrate (AgNO₃) in dimethylsulfoxide were successfully produced by the electrospinning method. Aqueous solution of hydrazinium hydroxide was used for the chemical reduction of silver ions. The effects of the simultaneous use of carbon nanotubes (either pristine or amine-functionalized) and silver nitrate in different percentages and the application of chemical reduction on the properties of the nanocomposite nanowebs were investigated. FTIR, SEM, conductivity meter, tensile tester, XRD, and DSC were used for the characterization. Antibacterial activities of the nanocomposite nanowebs were determined against S. Aureus. Full factorial experimental design was utilized in order to be able to evaluate the contributions of the selected factors (f-MWCNT content, AgNO₃ content, and application of reduction process) to the variations in ultimate tensile strength, elongation, and conductivity of the composite nanowebs. Analysis of variance (ANOVA) and multiple comparisons were carried out to evaluate the average nanofiber diameters and mechanical properties. PAN/f-MWCNTs/AgNPs nanowebs displayed enhanced conductivity and antimicrobial properties particularly when the chemical reduction process was applied. Besides they showed improved crystallinity compared with pure PAN nanofibers. While the reduction process made the highest contribution to the ultimate tensile strength, elongation, and conductivity of the nanowebs, f-MWCNT content had negligible effect on conductivity of the nanowebs. Considering all the results obtained in this study, composite nanofiber webs of PAN with 1 w% f-MWCNTs and 1 w%AgNO₃ can be suggested for use as antistatic and antibacterial filaments.

The development of electric circuit fabrication on flexible polymer substrates has attracted a significant interest as a pathway to low-cost, comfortable movement, and large-area electronics among direct printing techniques. In this study, the inkjet printing technique was used as a simple method to chemically deposit silver nano and micro-particles (85–500 nm) to the polyester fabrics. It is done by the ejection of silver nitrate and ascorbic acid as a reducing agent to attain nano metals on the different weave patterns with different surface roughness to measure the conductivity variations. A four-contact method was used to measure the electrical conductivity of the deposited samples which is usually employed in the electrical assessment of films. COMSOL Multiphysics® modeling software is used in order to simulate the conductivity of printed silver tracks and finally the results of simulation and experimental works have been compared. The main purpose of this study is to evaluate the effect of surface roughness on the electrical conductivity of printed silver tracks.

To estimate the photo-oxidation aging performance of PVC-coated membrane material in atmospheric conditions under tensile stresses, the relationship between physical and mechanical properties under accelerated weathering test and outdoor weathering test is studied with the same cumulative UV radiation energy. And then, both tensile strength and whiteness index were measured and compared to characterize the property change of membrane material after aging under four different tensile stresses (0%, 5%, 10% and 20% of the breaking strength), respectively. In addition, FTIR spectrometry was applied to characterize the chemical components of the samples under different weathering conditions, and the carbonyl index was extracted. The results show that there were significant differences of tensile strength and carbonyl index between two kinds of aging conditions, whereas with the increasing tensile stresses, the whiteness index represented a consistent increasing deviation of accelerated weathering from the outdoor weathering. However, the relationship have been built between both whiteness index and tensile strength retention of accelerated weathering and those of outdoor weathering conditions after a Schwarzschild’s modification. Therefore, the service lifespan of PVC-coated membrane materials can be evaluated by accelerated weathering tests under tensile stresses.

Phoenix sp. fiber-reinforced epoxy composites have been manufactured using compression molding technique. The effect of reinforcement volume content (0%, 10%, 20%, 30%, 40%, and 50%) and size (300 µm particles, 10 mm, 20 mm, and 30 mm fibers) on quasi-static and dynamic mechanical properties was investigated. Moreover, the water absorption properties of composites were analyzed at different environmental conditions (10℃, 30℃, and 60℃). For each reinforcement size, composites loaded with 40% in volume show highest tensile and flexural properties. Furthermore, composites with 300 µm particles present the best impact properties and the lowest water absorption, regardless of the environmental condition. The dynamic mechanical properties of the composites loaded with 40% in volume were analyzed by varying the reinforcement size and the load frequency (i.e., 0.5 Hz, 1 Hz, 2 Hz, 5 Hz, and 10 Hz). It was found that the glass transition temperature of short fiber-reinforced composites is higher than that of the composite loaded with particles.

A new flame-retardant protein viscose fiber with safely wearing performance has been prepared through blending protein solution, flame retardant (hexaphenoxycyclotriphosphazene) and viscose spinning solution, in which wool protein was used and added to spinning solution on the basis of 16% flame retardant, and the properties of the fiber were investigated. The product has more compact structure inside the fiber and evenly scattered small pores on the surface. Flame-retardant protein viscose fiber can reach the flame-retardant standard both before and after 30 times wash test, and the mechanical strength of the fiber was also improved. The introduction of hexaphenoxycyclotriphosphazene lowered the primary decomposition temperature of viscose fiber, reduced its weight loss. The flame-retardancy of the fiber can be improved by the introduction of protein. In thermal processes, the major product of thermal decomposition was CO₂, no hazardous and noxious gases were released. Due to the introduction of protein, moisture regain of the fiber is a little lower than that of viscose fiber, but higher than flame-retardant viscose fiber. Warmth retention property was also improved. Friction coefficient of the product is lower than that of flame-retardant viscose fiber. Bulking intensity was increased, which is better than that of viscose fiber.

In this paper, tungsten, bismuth, tin, and copper powders were used as additives in the fabric coating to obtain lead-free and flexible x-ray shielding material. The X-ray attenuation and the flexural properties of the coated fabrics were investigated considering the medical protection requirements. The results showed that tungsten additives in silicone rubber coating had better attenuation ratios than the samples that contain tungsten–tin, bismuth, and tungsten–copper, at same additive volume ratios. Moreover, the increment of tungsten volume ratios in coating blend resulted in higher shielding performance at same effective thicknesses and the lower silicone rubber amount in coating lead to compose thinner and lighter fabrics for equal protection level. In addition to that, the samples with tungsten–tin, bismuth, and tungsten–copper showed remarkable attenuation properties, and the results were found to be coherent with the theoretical values. The flex resistance and the flexural rigidity of the samples with tungsten content were also investigated. The coated fabrics with different powder loadings and thicknesses showed good resistance against repetitive folding; on the other hand, the results showed that the increment of tungsten amount in the coating resulted in stiffer fabrics.

In the smart textile area, textile antennas integrated into people’s clothing functioning as the wireless signal transmission devices have gained increasing attention in recent decades. In this study, a textile conformal dipole antenna was designed to work at the frequency of 915 MHz. The radiation elements of the antenna were adhered directly onto the stitched polyester fabric substrate to get the conformal effect. The measured results showed that the antenna had good performance with the return loss value and typical omnidirectional radiation patterns. To investigate the effect of textile substrate on the antenna performance, models for stitched and plain weave structures were built and the value of root mean square (RMS) surface error was calculated using integration methods. Then an acceptable range of operation frequencies versus RMS was marked out for estimating the reliability of textile substrate. The calculated RMS of our designed antenna was 0.25 mm, which was in the acceptable range area indicating the proper antenna design. Finally, the relationships between the critical frequencies and fabric parameters such as yarn thickness and density were studied, which gives the direct guideline for selecting the fabric as the substrate for textile antennas.