Experimental Characterization of the Influence of Tackifier Material on Preform Permeability

Abstract

Liquid composite molding processes use both simple and complex sets of preforms to produce high-performance composite parts. To produce these parts, binder materials known as tackifiers are used to shape the fabrics into complicated preforms prior to the resin injection. Tackifier materials enhance the formability and handling operations of dry reinforcements, and become an integral part of the composite laminate. A commercial tackifier was employed to form fiberglass preforms. Various preforms were prepared with different concentrations of the tackifier, and the effect on the permeability was studied. A permeability work-cell was used to continuously measure the permeability of the tackified preform for different fiber volume fractions. An analytical model based on a unit cell definition in combination with microscopic images was used to predict the permeability of tackified preforms. A comparison between the experimental measurement and the predicted results show the deficiencies in the unit cell approach to model permeability of preforms containing low concentrations of tackifiers.

Keywords

tackifier binders permeability resin transfer molding unit cell microstructure

Get full access to this article

View all access options for this article.

References

1. Karbhari, V.M. , Slotte, S.G. , Steenkamer, D.A. and Wilkins, D.J. (1992). Effect of Material, Process, and Equipment Variables on the Performance of Resin Transfer Moulded Parts, Composites Manufacturing, 3(3).

2. Horn, S. (1990). Complex Structural Shape Performing Process Technology. In: Proceedings of the sixth Annual ASM/ESD, 8–11 October.

3. Mohan, R.V., Bickerton, S., Shires, D.R., Advani, S.G. and Tamma, K.K. Analysis and Characterization of Flow Channels During Manufacturing of Composites by Resin Transfer Molding, ANTEC ’97.

4. Bickerton, S. and Advani, S.G. (1999). Characterization and Modeling of Race-Tracking in Liquid Composite Molding Processes, Composites Science and Technology, 59-59.

5. Shis, C.H. , Liu, Q. and Lee, J. (1999). Tackification and High Temperature Vacuum-Assisted RTM-SCRIMP, 31st International SAMPE Technical Conference, 26–30 October.

6. Hillermeier, R.W. , Hayes, B.S. and Seferis, J.C. (1999). Processing and Performance of Tackifier-Toughened Composites for Resin Transfer Molding Techniques, 44th International SAMPE Symposium, 23–27 May.

7. Hillermeier, R.W. , Hayes, B.S. and Seferis, J.C. (2000). Tackifier/Binder Toughened Resin Transfer Molding Composites, Journal of Advanced Materials, 32(3).

8. Brinkman, G. , Cadenas-Montes, C. , Phillips, R. , Arnold and Bowman, K. (1995). Evaluation of Tackifier Agents for Resin Transfer Molding, 40th International SAMPE Symposium and Exhibition, 8–11 May.

9. Kittelson, J. and Hackett, S.C. (1994). Tackifier/Resin Compatibility is Essential for Aerospace Grade Resin Transfer Molding, Moving Forward with 50 Years of Leadership in Advanced Materials, SAMPE, 39.

10.

10. Rohatgi, V. and Lee, J. (1997). Moldability of Tackified Fiber Preforms in Liquid Composite Molding, Journal of Composite Materials, 31(7).

11.

11. Weitzenbock, J.R. , Shenoi, R.A. and Wilson, P.A. (1999). Radial Flow Permeability Measurement. Part A: Theory, Composites Part A, 30: 781–796.

12.

12. Weitzenbock, J.R. , Shenoi, R.A. and Wilson, P.A. (1999). Radial Flow Permeability Measurement. Part B: Application, Composites Part A, 30: 797–813.

13.

13. Stadfeld, H.C. , Erninger, M. , Bickerton, S. and Advani, S.G. (2001). An Experimental Method to Continuously Measure Permeability of Fiber Preforms, Paper submitted to Journal of Reinforced Plastics.

14.

14. Binetruy, C. , Hilaire, B. and Pabiot, Jose (1997). The Interactions Between Flows Occurring Inside and Outside Fabric Tows During RTM, Composite Science and Technology, 57: 587–596.

15.

15. Gembinski, J. (1990). The Role of Preforms in Higher Volume Composites. In: Proceedings of the sixth Annual ASM/ESD, 8–11 October.

16.

16. Simacek, P. and Advani, Suresh (1996). Permeability Model for a Woven Fabric, Polymer Composites, 17(6).

17.

17. Simacek, P., Sozer, E.M. and Advani, S. User Manual for DRAPE 1.1 and LIMS 4.0 (Liquid Injection Molding Simulation), University of Delaware, Center for Composite Materials Technical Report 98-01.