Polyamide 11-MWNT nanocomposites: Thermal and electrical conductivity measurements

Abstract

Multi-wall carbon nanotubes (MWNTs) with different loadings (0, 1, 3, 5, 7 and 9 wt%) were incorporated into polyamide 11 using a powder–powder mixing technique to form nanocomposites. The density and specific heat of each nanocomposite were measured. Thermal conductivities of these polymer nanocomposite powders were measured in a nitrogen atmosphere using a commercial transient plane-source device. Results indicate the thermal conductivity of preheated powder was larger than the fresh powder and similar to that at the melting temperature. The powder formulations were also pressed into films using a heat press and room temperature electrical conductivity measurements were performed. Substantial improvements in electrical conductivity were observed with increasing loading of MWNT. Microstructures of the nanocomposite specimens were examined using scanning electron microscopy.

Keywords

Polyamide 11–multi-wall carbon nanotube nanocomposite thermal conductivity electrical conductivity polyamide

Get full access to this article

View all access options for this article.

References

Berry

Brown

Connell

. Preliminary experience with medical applications of rapid prototyping by selective laser sintering. Med Eng Phys 1996; 19: 90–96.

Savas B, Kwon Y-Y and Tomanek D. Unusually high thermal conductivity of carbon nanotubes. Phys Rev Lett 2000; 84: 4613.

Dressler

Rolling

Schmidt

. Temperature distribution in powder beds during 3D printing. Rapid Prototyping J 2010; 16: 16–25.

Saxena

Chohan

Gustafsson

. Effective thermal conductivity of loose granular materials. J Phys D: Appl Phys 1985; 19: 1625–1630.

Xue J and Barlow JW. Thermal properties of powders. In: Solid freeform fabrication symposium proceedings, Austin, TX, 1990, pp. 179–185.

Deissler

Boegli

. An investigation of elective thermal conductivities of powders I various gases. Trans Am Soc Mech Eng 1958, pp. 1417–1417.

Yuan M. Thermal conductivity measurements of polyamide 12. In: Solid freeform fabrication symposium proceedings, Austin, TX 2011, pp. 427–437.

Meincke

Kaempfer

Weickmann

. Mechanical properties and electrical conductivity of carbon-nanotube filled polyamide-6 and its blends with acrylonitrile/butadiene/styrene. Polymer 2004; 45(3): 739–748.

Yan

Yang

. An innovative method to improve the electrical conductivity of multi-walled carbon nanotubes filled polyamide 6/polystyrene blends. Mater Lett 2009; 63(22): 1900–1903.

10.

Lao SC, Wu C, Moon TJ, et al. Flame-retardant polyamide 11 and 12 nanocomposites: thermal and flammability properties. J Compos Mater 2009; 43(17): 1803–1818.

11.

Lao SC, Yong W, Nguyen K, et al. Flame-retardant polyamide 11 and 12 nanocomposites: processing, morphology, and mechanical properties. J Compos Mater 2010; 44(25): 2922–2951.

12.

Arkema. Graphistrength C100 MWNT technical data sheet, Arkema, France, www.graphistrength.com (2009, accessed 21 May 2013).

13.

Chen DZ, Lao SC, Koo JH et al. Selective laser sintering of conductive polyamide 11-MWNT nanocomposites for lower percolation threshold. In: Proceedings of 2011 SAMPE ISSE, SAMPE, Covina, CA, 2011.

14.

Gallagher DP and Liang R. Laser Flash Apparatus (LFA) 457 Microflash, PPT, Florida State University, Tallahassee, FL.

15.

Gauthier MM. Engineering plastics. In: ASM engineered materials handbook, vol. 2, ASM Intl, 1985, p. 60.

16.

Moisala

Kinloch

. Thermal and electrical conductivity of single and multi-walled carbon nanotube-epoxy composites. Compos Sci Technol 2006; 66: 1285–1288.

17.

Lemmon

Jacobsen

. Viscosity and thermal conductivity equations for nitrogen, oxygen, argon, and air. Int J Thermophys 2004; 25: 21–21.