Effect of Hybridization on the Creep and Stress Relaxation Characteristics of Pultruded Composites

Abstract

Pultrusion manufacturing process is a well established technique for the cost-effective production of high-modulus and lightweight composite materials having constant cross-sectional profiles. The pultruded composites are widely used as structural members viz., beams, trusses and stiffeners, owing to the presence of high proportion of axial fibers necessary to sustain large tractive forces. These structural members are subjected to a combination of static and dynamic loading conditions at wide temperature ranges and over longer periods. Since polymeric composites exhibit viscoelastic behavior, the effectiveness of these materials as structural members must be thoroughly evaluated to ensure long-term stability. In previous research, the dynamic performance characteristics of pultruded glass-graphite/epoxy hybrids were evaluated at room temperature. The effects of temperature, frequency, post-curing, along with the type and placement of fibers on the dynamic flexural properties of glass/epoxy and hybrid glass-graphite/epoxy were also investigated.

This paper focuses on the evaluation of creep and stress relaxation performance characteristics of pultruded glass-graphite/epoxy hybrid composites. Dynamic mechanical analysis technique was adopted for the accelerated creep and stress relaxation testing. Time-temperature superposition principle, which greatly reduced the experimental time, was effectively utilized for predicting the creep and stress relaxation properties of the hybrid composites. Results indicate that the type and amount of fibers as well as their lay-up sequence plays a significant role in determining the flow and load bearing characteristics.

Keywords

pultrusion composites hybridization viscoelasticity dynamic mechanical analysis creep stress relaxation time-temperature superposition flexural creep compliance flexural relaxation modulus.

Get full access to this article

View all access options for this article.

References

1. Gibson, R. F. 1994. Principles of Composite Material Mechanics. McGraw-Hill Inc.

2. Kumar, P.1994. "Study of Static Mechanical Properties of Pultruded Hybrid Graphite/Glass Epoxy Composites," M.S. thesis, the University of Mississippi.

3. Vaughan, J. G. 1988. "Use of Statistical Design Experimentation to Characterize and Optimize the Pultrusion Process," 43rdAnnual Conference, Composites Institute, The Society of Plastics Industry, Inc., 6-D: 1-6, February 1-5.

4. Holmes, J. W. 1992. "A Technique for Tensile Fatigue and Creep Testing of Fiber Reinforced Ceramics," Journal of Composite Materials, 26(9):917-933.

5. Wang, Y. R. and T. W. Chou . 1992. "Analytical Modeling of Creep Behavior of Short Fiber Reinforced Ceramic Matrix Composites," Journal of Composite Materials, 26(9):1269-1286.

6. Li, J. and G. J. Weng . 1994. "Effective Creep Behavior and Complex Moduli of Fiber and Ribbon-Reinforced Polymer Matrix Composites," Composites Science and Technology, 52:615-629.

7. D'Amore, A , A. Pompo and L. Nicolais . 1991. "Viscoelastic Effects in Poly(Ether Ether Ketone) (PEEK) and PEEK-Based Composites," Composites Science and Technology, 41:303-325.

8. Yen, S. C. and F. L. Williamson . 1990. "Accelerated Characterization of Creep Response of an Off-Axis Composite Material," Composites Science and Technology, 38:103-118.

9. Gibson, R. F. , S. J. Hwang and C. H. Sheppard . 1990. "Characterization of Creep in Polymer Composites by the Use of Frequency-Time Transformations," Journal of Composite Materials, 24:441-453.

10.

10. Sullivan, J. L.

"Creep and Physical Aging of Composites,"

Composites Science and Technology, 39:207-232.

11.

11.Barpanda, D.1995. "Effects of Time and Temperature on the Dynamic Flexural Properties of Pultruded Hybrid Composites,"M.S. thesis, the University of Mississippi.

12.

12. 1993. 983 DMA Operator's Manual. TA Instruments, Delaware.

13.

13. Ferry, J. D. 1980. Viscoelastic Properties of Polymers, 3rd ed New York: John Wiley and Sons Ltd.

14.

14. Rosen, S. L. 1971. Fundamental Principles of Polymeric Materials for Practicing Engineers. Barnes and Noble Inc., pp. 229-232.

15.

15. Aklonis, J. J. , W. J. MacKnight and M. Shen . 1972. Introduction to Polymer Viscoelasticity. New York: Wiley-Interscience.

16.

16. Mantena, P. R. , R. Vangipuram and J. G. Vaughan . 1994. "Dynamic Flexural Properties of Pultruded Glass/Graphite Hybrid Composites," Proceedings of the 39th International SAMPE Symposium and Exhibition, Anaheim, CA, April 11-14, 39:174-182.

17.

17. Barpanda, D. and P. R. Mantena . 1996. "Dynamic Mechanical Analysis of Pultruded Glass-Graphite/Epoxy Hybrid Composites at Elevated Temperatures," Journal of Reinforced Plastics and Composites, 15(5):497-532