Characteristics of a volume-adjustable compression chamber for transradial prosthetic interface

Abstract

In the transradial limb–socket contact interface, the physiological properties and prosthetic operating habits of the residual limb might affect the comfort and functionality of the prosthesis. To enhance the comfort and functionality of the interface, a frame-type socket with four volume-adjustable compression chambers was proposed for the transradial amputation level. The contact pressure of the limb–socket interface was adjusted by the volume changes in the chambers and controlled by a vacuum pump and the corresponding control system. The parameters of the chamber were designed in accordance with the biomechanics of the forearm soft tissue. The chamber with a negative stiffness characteristic was theoretically compared with the chamber with a positive stiffness characteristic. The results showed that the former had a superior performance to the latter in safety and pump performance requirements. A physical model of the transradial frame-type prosthetic interface was also manufactured with four negative stiffness chambers. The experimental results showed that this new prosthetic interface achieved more fitting time and better performance in comfort and functionality than the fixed frame-type socket. This new prosthetic interface with volume-adjustable compression chambers might be an alternative choice for transradial amputees.

Keywords

Upper-limb prostheses prosthetic interface prosthetic socket transradial prosthesis forearm rehabilitation

Get full access to this article

View all access options for this article.

References

Dudkiewicz

Gabrielov

Seiv-Ner

. Evaluation of prosthetic usage in upper limb amputees. Disabil Rehabil 2004; 26: 60–63.

Watve

Dodd

MacDonald

. Upper limb prosthetic rehabilitation. Orthop Trauma 2011; 25: 135–142.

Plettenburg

. Basic requirements for upper extremity prostheses: the WILMER approach. In: Proceedings of the 20th annual international conference of the IEEE engineering in medicine and biology society, Hong Kong, China, 28 October–1 November 1998, pp.2276–2281. New York: IEEE.

Biddiss

Beaton

Chau

Consumer design priorities for upper limb prosthetics. Disabil Rehabil Assist Technol 2007; 2: 346–357.

Zheng

Zhao

BH.

3D reconstruction of the structure of a residual limb for customising the design of a prosthetic socket. Med Eng Phys 2005; 27: 67–74.

Lake

The evolution of upper limb prosthetic socket design. J Prosthet Orthot 2008; 20: 85–92.

Biddiss

Chau

Dielectric elastomers as actuators for upper limb prosthetics: challenges and opportunities. Med Eng Phys 2008; 30: 403–418.

Esquenazi

Amputation rehabilitation and prosthetic restoration. From surgery to community reintegration. Disabil Rehabil 2004; 26: 831–836.

Sauter

Naumann

Milner

A three-quarter type below-elbow socket for myoelectric prostheses. Prosthet Orthot Int 1986; 10: 79–82.

10.

Alley

. Advancement of upper extremity prosthetic interface and frame design. In: Proceedings of the 2002 myoelectric symposium, 2002, http://dukespace.lib.duke.edu/dspace/bitstream/handle/10161/2684/r_alley_paper01.pdf?sequence=3

11.

Miguelez

Lake

Conyers

. The transradial anatomically contoured (TRAC) interface: design principles and methodology. J Prosthet Orthot 2003; 15: 148–157.

12.

Alley

RD.

Biomechanical discussions of current and emerging upper-limb prosthetic interface designs. Acad Today 2009; 5: 1–8.

13.

Alley

. The high-fidelity interface skeletal stabilization through alternating soft tissue. In: Proceedings of the 2011 myoelectric controls/powered prosthetics symposium fredericton, 2011, http://dukespace.lib.duke.edu/dspace/bitstream/handle/10161/4746/59%20Alley.pdf?sequence=1

14.

Kenney

LPJ

Lisitsa

Bowker

. Dimensional change in muscle as a control signal for powered upper limb prostheses: a pilot study. Med Eng Phys 1999; 21: 589–597.

15.

Mak

AFT

Zhang

Boone

DA.

State-of-the-art research in lower-limb prosthetic biomechanics-socket interface: a review. J Rehabil Res Dev 2001; 38: 161–173.

16.

Jönsson

Caine-Winterberger

Brånemark

Osseointegration amputation prostheses on the upper limbs: methods, prosthetics and rehabilitation. Prosthet Orthot Int 2011; 35: 190–200.

17.

Mak

AFT

Liu

Lee

SY.

Biomechanical assessment of below-knee residual limb tissue. J Rehabil Res Dev 1994; 31: 188–198.

18.

Zheng

Mak

AFT

. Effective elastic properties for lower limb soft tissues from manual indentation experiment. IEEE Trans Rehabil Eng 1999; 7: 257–267.

19.

Zhang

Zheng

Mak

AFT

. Estimating the effective Young’s modulus of soft tissues from indentation tests–nonlinear finite element analysis of effects of friction and large deformation. Med Eng Phys 1997; 19: 512–517.

20.

Chen

Lan

CC.

An adjustable constant-force mechanism for adaptive end-effector operations. J Mech Design 2012; 134: 031005.

21.

Lan

CC.

Linear variable-stiffness mechanisms based on preloaded curved beams. J Mech Design 2014; 136: 122302.

22.

Steinbuch

Design of a transradial socket. Delft: Delft University of Technology (TU Delft), 2010.

23.

Bertels

Kettwig

. Breathable liner for transradial prostheses. In: Proceedings of the 2011 myoelectric symposium, 2011, http://dukespace.lib.duke.edu/dspace/bitstream/handle/10161/4719/15%20Bertels.pdf?sequence=1

24.

Wilson

Jr Schuch

Nitschke

RO.

A variable volume socket for below-knee prostheses. Clin Prosthet Orthot 1987; 11: 11–19.

25.

Pinzur

Angelico

Quigley

MJ.

A volume-adaptable prosthesis for ankle disarticulation. J Prosthet Orthot 1993; 5: 77.

26.

Sanders

Fatone

Residual limb volume change: systematic review of measurement and management. J Rehabil Res Dev 2011; 48: 949–986.

27.

Sanders

Cassisi

DW.

Mechanical performance of inflatable inserts used in limb prosthetics. J Rehabil Res Dev 2001; 38: 365.

28.

Greenwald

Dean

Board

WJ.

Volume management: smart variable geometry socket (SVGS) technology for lower-limb prostheses. J Prosthet Orthot 2003; 15: 107–112.

29.

Sanders

Jacobsen

Fergason

JR.

Effects of fluid insert volume changes on socket pressures and shear stresses: case studies from two trans-tibial amputee subjects. Prosthet Orthot Int 2006; 30: 257–269.

30.

Ogawa

Obinata

Hase

. Design of lower limb prosthesis with contact pressure adjustment by MR fluid. In: 30th annual international conference of the IEEE engineering in medicine and biology society (EMBS 2008), Vancouver, BC, Canada, 20–25 August 2008, pp.330–333. New York: IEEE.

31.

Mak

AFT

Kwan

LPC

. Deformation and reperfusion damages and their accumulation in subcutaneous tissues during loading and unloading: a theoretical modeling of deep tissue injuries. J Theor Biol 2011; 289: 65–73.

32.

Gefen

van Nierop

Bader

. Strain-time cell-death threshold for skeletal muscle in a tissue-engineered model system for deep tissue injury. J Biomech 2008; 41: 2003–2012.

33.

Stekelenburg

Strijkers

Parusel

. Role of ischemia and deformation in the onset of compression-induced deep tissue injury: MRI-based studies in a rat model. J Appl Physiol 2007; 102: 2002–2011.

34.

Demol

Van Deun

Haex

. Modelling the effect of repositioning on the evolution of skeletal muscle damage in deep tissue injury. Biomech Model Mechanobiol 2013; 12: 267–279.

35.

Houwing

Overgoor

Kon

. Pressure-induced skin lesions in pigs: reperfusion injury and the effects of vitamin E. J Wound Care 2000; 9: 36–40.