An experimental investigation on the influence of deactivation of a groove on the performance of a twin groove journal bearing

Abstract

Laboratory tests have been carried out in order to assess the influence of groove activation and deactivation on the performance of a twin axial groove steadily loaded hydrodynamic journal bearing. Temperature distribution at the oil–bush interface, oil outlet temperature, total oil flow rate, partial oil flow rate (at each groove), and motor consumption were measured for several journal speeds and loads under constant feeding pressure (p_f) and constant feeding temperature (T_f), at five different loading angles (Γ). In this study, the corresponding groove was deactivated whenever negative oil flow rate was observed in it and results were compared. It was found that the groove deactivation strategy has profound influence on the bearing performance when negative flow rate occurs at one groove, preventing such undesirable effects as lubricant starvation at the loaded region of the bearing. Groove deactivation in the event of negative flow rate may be easily implemented by incorporating a check valve to the feeding system of each groove. Such strategy seems to be highly recommended for the safe operation of bearings subjected to high loads and load angles deviated from 90°.

Keywords

Hydrodynamic journal bearings supply conditions thermal behavior groove deactivation

Get full access to this article

View all access options for this article.

References

Tonnesen

Hansen

. Some experiments on the steady state characteristics of a cylindrical fluid film bearing considering thermal effects. ASME J Lubr Technol 1981; 103: 107–114.

Lund

Tonnesen

. An approximate analysis of the temperature conditions in a journal bearing. Part ii: Application. ASME J Tribol 1984; 106: 237–245.

Fitzgerald

Neal

. Temperature distributions and heat transfer in journal bearings. ASME J Tribol 1992; 114: 122–130.

Taylor

. An experimental investigation of thermal effects in circular and elliptical plain journal bearings. Tribol Int 1996; 29: 19–26.

Ferron

Frêne

Boncompain

. A study of the thermohydrodynamic performance of a plain journal bearing. Comparison between theory and experiments. ASME J Lubr Technol 1983; 105: 422–428.

Gethin

El-Deihi

MKI

. Thermal behavior of a twin axial groove bearing under varying loading direction. Proc IMechE, Part A: J Power and Energy 1990; 204: 77–90.

Brito

Bouyer

Fillon

. Experimental investigation of the influence of supply temperature and supply pressure on the performance of a two axial groove hydrodynamic journal bearing. ASME J Tribol 2007; 129: 98–105.

Brito

Miranda

Pimenta Claro

. The role of lubricant supply temperature on the performance of twin groove journal bearings: An experimental study. Int J Surf Sci Eng 2011; 5: 286–299.

Arab Solghar

Brito

Claro

JCP

. An experimental study of the influence of loading direction on the thermohydrodynamic behavior of twin axial groove journal bearing. Proc IMechE, Part J: J Engineering Tribology 2011; 225: 245–254.

10.

Brito

Miranda

Claro

JCP

. Experimental comparison of the performance of a journal bearing with a single and a twin axial groove configuration. Tribol Int 2012; 53: 1–8.

11.

Claro

JCP

Miranda

. Analysis of hydrodynamic journal bearings considering lubricant supply conditions. Proc IMechE, Part C: J Mechanical Engineering Science 1993; 207: 93–101.

12.

Costa

Miranda

Claro

JCP

. Temperature, flow, and eccentricity measurements in a journal bearing with a single axial groove at 90° to the load line. Lubr Sci 2003; 15: 147–161.

13.

Brito FP, Miranda AS, Claro JCP, et al. The role of each groove on the behavior of twin axial groove journal bearings. In: IV Iberian Tribology Congress, Bilbao, Spain, 21–22 June 2007. (CD-ROM).