Usually, rotor dynamic analyses do not consider the effects of the lubricant supply condition, although this is an important aspect of journal bearing performance. Therefore, this work has implemented a mass-conserving model to realistically describe the oil feeding condition and evaluate its influence on rotor dynamics. This analysis was carried out by varying feeding pressure and groove position and the results indicate that the oil supply conditions significantly influence the bearing performance and affect the dynamic behavior of the entire rotor. In general, lower flow rates lead to a bearing with a greater stability region, as observed mainly in the bearing with a groove at 270° and, on the other hand, the increase in feeding pressure reduces the instability threshold.
HeMAllairePBarrettL, et al.Thermohydrodynamic modeling of leading-edge groove bearings under starvation condition. Tribol Trans2005; 48: 362–369.
4.
RoyLMajumdarBC. Effect of the location of axial groove on the steady state and dynamic characteristics of oil journal bearings. In: Proc 12th national conference on machines and mechanisms (NaCoMM 2005). 2005(July), pp.261–268.
5.
RoyLLahaSK. Steady state and dynamic characteristics of axial grooved journal bearings. Tribol Int2009; 42: 754–761.
6.
WangLLWeiYLYuanGT, et al.Analysis of steady state characteristics for single-axial groove sleeve bearing. IOP Conf Ser Mater Sci Eng2018; 389: 012013.
7.
JakobssonB. The finite journal bearing, considering vaporization. Trans Chalmers Univ Technol1957; 190: 35–47.
8.
FlobergL. Lubrication of two rotating cylinders at variable lubricant supply with reference to the tensile strength of the liquid lubricant. J Lubr Technol1973; 95: 155–163.
9.
OlssonK. Cavitation in dynamically loaded bearings. Trans Chalmers Univ Technol1965; 308: 12–27.
VijayaraghavanDKeithTG. Development and evaluation of a cavitation algorithm. Tribol Trans1989; 32: 225–233.
12.
AusasRFJaiMBuscagliaGC. A mass-conserving algorithm for dynamical lubrication problems with cavitation. J Tribol2009; 131: 1–7.
13.
VijayaraghavanDKeithTG. Effect of type and location of oil groove on the performance of journal bearings. Tribol Trans1992; 35: 98–106.
14.
ClaroJCPMiranda AAS. Analysis of hydrodynamic journal bearings considering lubricant supply conditions. Proc IMechE, Part C: J Mechanical Engineering Science1993.
15.
VijayaraghavanDKeithTGBreweDE. Effect of lubricant supply starvation on the thermohydrodynamic performance of a journal bearing. Tribol Trans1996; 39: 645–653.
16.
PierreIFillonM. Influence of geometric parameters and operating conditions on the thermohydrodynamic behaviour plain journal bearings. Proc IMechE, Part J: J Engineering Tribology2000; 214: 445–457.
17.
CostaLMirandaASFillonM, et al.An analysis of the influence of oil supply conditions on the thermohydrodynamic performance of a single-groove journal bearing. Proc IMechE, Part J: J Engineering Tribology2003; 217: 133–144.
18.
BritoFPMirandaASClaroJCP, et al.The role of lubricant feeding conditions on the performance improvement and friction reduction of journal bearings. Tribol Int2014; 72: 65–82.
19.
BritoFCMirandaASClaroJP, et al.Experimental study of the influence of groove flow rate on the performance of a single and a twin axial groove journal bearing. In: Society of tribologists and lubrication engineers—2008 annual meeting and exhibition, extended abstracts2008;(January), pp.2–5.
20.
BritoFPMirandaASClaroJCP, et al.Experimental comparison of the performance of a journal bearing with a single and a twin axial groove configuration. Tribol Int2012; 54: 1–8.
21.
AhmadMAKasolangSDwyer-joyceR, et al.The effects of Oil groove position on torque and frictional force in hydrodynamic journal bearing. Appl Mech Mater2013; 393: 907–912.
22.
AhmadMAKasolangSDwyer-JoyceR. The effects of oil supply pressure at different groove position on frictional force and torque in journal bearing lubrication. Procedia Eng2013; 68: 70–76.
23.
AhmadMAKasolangSDwyer-JoyceR. Experimental study of Oil supply pressure effects on bearing friction in hydrodynamic lubrication. Appl Mech Mater2013; 315: 977–981.
24.
NewkirkBLTaylorHD. Shaft whipping due to oil action in journal bearings. Gen Electr Rev1925; 28: 559–568.
25.
WangJKKhonsariMM. Effects of oil inlet pressure and inlet position of axially grooved infinitely long journal bearings. Part I : analytical solutions and static performance. Tribol. Int2008; 41: 119–131.
26.
WangJKKhonsariMM. Effects of oil inlet pressure and inlet position of axially grooved infinitely long journal bearings. Part II : nonlinear instability analysis $. Tribol Int2008; 41: 132–140.
27.
NicholsBRFittroRLGoyneCP. Rotor damped natural frequencies and stability under reduced oil supply flow rates to tilting-pad journal bearings. J Eng Gas Turbines Power2018; 140: 1–10.
28.
NicholsBRFittroRLGoyneCP. Subsynchronous vibration patterns under reduced oil supply flow rates. J Eng Gas Turbines Power2018; 140: 102503.
29.
LundJW. Spring and damping coefficients for the tilting-pad journal bearing. ASLE Trans1964; 7: 342–352.
30.
LundJW. Review of the concept of dynamic coefficients for fluid film journal bearings. J Tribol1987; 109: 37–41.
31.
NelsonHD. A finite rotating shaft element using Timoshenko beam theory. J Mech Des1980; 102: 793–803. Available DOI: 10.1115/1.3254824
32.
BritoFP. Thermohydrodynamic performance of twin groove journal bearings considering realistic lubricant supply conditions: an experimental and theoretical study. Universidade do Minho, 2009.
