This study determines the influence of mechanical surfacing on tensile shear strength (TSS) and wood failure percentage (WFP) of beech wood (Fagus sylvatica L.) at the wet stage according to prEN 302-1:2011 (tensile shear tests). The wood was planed, sanded and face milled, using different qualities of cutting edges and sanding grits. Roughness and wettability of the adherends were characterised, supplemented by environmental scanning electron microscopy images. The specimens were bonded by means of a one-component polyurethane adhesive and tested at the dry stage (pretreatment A1), at the wet stage (A4) and after re-drying (mA5). Results determined that the wettability and the wood structure's integrity are considered more decisive for the TSS at the wet stage than surface roughness. Planing with very dull knives caused the lowest TSS and WFP after A4 and the most subsurface damage. Face milled and sanded batches revealed the best performance. The TSS and WFP decreased significantly from A1 to A4, but recovered after mA5.
ASTM D2559-04. 2004. Standard specification for adhesives for structural laminated wood products for use under exterior (wet use) exposure conditions. ASTM International, West Conshohocken, PA, USA.
2.
BustosC. A., MoyaC. L., LisperguerJ. M., and ViverosE. M.. 2010. Effect of knife wear on the gluability of planed surfaces of radiata pine.Wood Fiber Sci.42: 185–191.
3.
CoolJ., and HernandezR. E.. 2011a. Evaluation of four surfacing methods on black spruce wood in relation to poly(vinylacetate) gluing performance.Wood Fiber Sci.43: 194–205.
4.
CoolJ., and HernandezR. E.. 2011b. Improving the sanding process of black spruce wood for surface quality and water-based coating adhesion.For. Prod. J. 61: 372–380.
5.
CSA O112·9-04 2004. Evaluation of adhesives for structural wood products (exterior exposure). Canadian Standards Association, Toronto, Canada.
de MouraL. F., CoolJ., and HernandezR. E.. 2010. Anatomical evaluation of wood surfaces produced by oblique cutting and face milling.IAWA J.31: 77–88.
8.
DIN EN15425:2008. Adhesives – one component polyurethane for load bearing timber structures – classification and performance requirements. Deutsches Institut für Normung, Berlin, Germany.
9.
DIN EN1995-1-1:2010. Eurocode 5: design of timber structures. Part 1-1: General- common rules and rules for buildings; German version EN1995-1-1:2004+AC:2006+A1:2008. Deutsches Institut für Normung, Berlin, Germany.
10.
DIN EN ISO 4287:2010. Geometrical product specifications (GPS) – surface texture: profile method – terms, definitions and surface texture parameters. Deutsches Institut für Normung, Berlin, Germany.
11.
FollrichJ., VayO., VeigelS., and MüllerU.. 2010. Bond strength of end-grain joints and its dependence on surface roughness and adhesive spread.J. Wood Sci. 56: 429–434.
12.
FritzA. H., and SchulzeG.. 2008. Fertigungstechnik, Berlin, Springer.
13.
GindlM., ReitererA., SinnG., and Stanzl-TscheggS. E.. 2004. Effects of surface ageing on wettability, surface chemistry, and adhesion of wood.Holz Roh Werkst62: 273–280.
14.
Greiner-MaiD.. 2006. Gutachten zu den Ursachen des Einsturzes der Eissporthalle in Bad Reichenhall vorgelegt.Bautechnik83: 667–668.
15.
HeiselU., and TrögerJ.. 1993. Qualitativ hochwertige Oberflächen durch Stirnplanfräsen.HOB40: 80–88.
16.
HernandezR. E., and CoolJ.. 2008a. Effects of cutting parameters on surface quality of paper birchwood machined across the grain with two planing techniques.Holz Roh Werkst66: 147–154.
17.
HernandezR. E., and CoolJ.. 2008b. Evaluation of three surfacing methods on paper birch wood in relation to water- and solvent-borne coating performance.Wood Fiber Sci.40: 459–469.
18.
ISO 3002/1. 1982. Basic quantities in cutting and grinding. Part 1: Geometry of the active part of cutting tools – general terms, reference systems, tool and working angles, chip breakers. International Organization for Standardization, Geneva, Switzerland.
19.
ISO 3002/3. 1984. Basic quantities in cutting and grinding. Part 3: Geometric and kinematic quantities in cutting. International Organization for Standardization, Geneva, Switzerland.
20.
KollmannF.. 1951. Technologie des Holzes und der Holzwerkstoffe, Berlin, Springer.
21.
MaierG.. 2000. Holzspanungslehre und werkzeugtechnische Grundlagen, Würzburg, Vogel, Kamprath-Reihe.
22.
MurmanisL., RiverB. H., and StewartH. A.. 1986. Surface and subsurface characteristics related to abrasive-planing conditions.Wood Fiber Sci.18: 107–117.
23.
NiemzP.. 1993. Physik des Holzes und der Holzwerkstoffe, Leinfelden-Echterdingen, DRW.
24.
NussbaumR. M.. 1999. Natural surface inactivation of Scots pine and Norway spruce evaluated by contact angle measurements.Holz Roh Werkst57: 419–424.
25.
PahlitzschG., and SchulzK.. 1957. Schnittkraftmessung und Schneidenabstumpfung beim Hobeln von Holz mit kreisender Schnittbewegung.Holz Roh Werkst15: 159–170.
26.
prEN 301:2011. Adhesives, phenolic and aminoplastic, for load-bearing timber structures – classification and performance requirements. European Committee for Standardization, Brussels, Belgium.
27.
prEN 302-1:2011. Adhesives for load-bearing timber structures. Test methods. Part 1: Determination of longitudinal tensile shear strength. European Committee for Standardization, Brussels, Belgium.
28.
prEN 828:2010. Adhesives – wettability – determination by measurement of contact angle and surface free energy of solid surface. European Committee for Standardization, Brussels, Belgium.
29.
RichterK., and SchirleM. A.. 2002. Behaviour of 1K PUR adhesives under increased moisture and temperature conditions. In Teischinger and Stingl. In Lignovisionen, Proceedings of the international Symposium on Wood Based Materials, BOKU Vienna 2002:p. 153–158.
30.
RiegelA.. 1997. Gefügeschädigungen durch spanende Bearbeitung – Stand der Erkenntnisse und mögliche Messmethoden.Holz Roh Werkst55: 111–117.
31.
RiverB. H., VickC. B., and GillespieR. H.. 1991. Wood as an adherend. New York, Marcel Dekker.
32.
SantoniI., and PizzoB.. 2011. Effect of surface conditions related to machining and air exposure on wettability of different Mediterranean wood species.Int. J. Adhes. Adhes. 31: 743–753.
33.
SinghA. P., AndersonC. R., WarnesJ. M., and MatsumuraJ.. 2002. The effect of planing on the microscopic structure of Pinus radiata wood cells in relation to penetration of PVA glue.Holz Roh Werkst60: 333–341.
34.
VolkR.. 2005. Rauheitsmessung: Theorie und Praxis, DIN e.V., Berlin, Beuth.
35.
WellonsJ. D.. 1980. Wettability and gluability of Douglas-fir Veneer.For. Prod. J. 30: 53–55.
