Maximal singularity-free distribution of input parameters in a parallel manipulator considering load deformations and clearances

Abstract

It is well known that singularities are inherent to parallel manipulators and have serious influence on their properties. It is desired that the motion uncertainty caused by the singularity should be avoided in the design and operation stages. The singularity distribution hypersurface shows the relations among the pose components at the singular points, but it is difficult to be utilized in predicting the motion certainty through checking and controlling the lengths of input parameters. In this article, taking a 3-RPR parallel manipulator as an example, and considering the clearances existing in the joints and the deformations of the input actuating cylinders under external loads, the maximal singularity-free distribution of input parameters is investigated. While the input parameters are located within the space enveloped by the maximal singularity-free distribution surfaces, the manipulator can bear the required external loads and give out a certain motion at the neighbourhood of singular points. Based on this kind of the maximal singularity-free distribution of input parameters, the singularity can be avoided both in the early design stage by assigning the input parameters into a suitable region and in the operation state through controlling and monitoring the values of the input parameters.

Keywords

3-RPR parallel manipulator singularity-free distribution

Get full access to this article

View all access options for this article.

References

Hunt

K. H.

, Kinematic geometry of mechanisms (Oxford: Oxford University Press 1978).

Fichter

E. F.

, ‘A Stewart platform-based manipulator: general theory and practical construction’ Int. J. Robot. Res. 5 2 (1986): 157–182.

Gosselin

Angeles

, ‘Singularity analysis of closed-loop kinematic chains’ IEEE Trans. Robot. Autom. 6 3 (1990): 281–290.

Zlatanov

Fenton

R. G.

Benhabib

, ‘Singularity analysis of mechanisms and robots via a motion-space model of the instantaneous kinematics’ In Proceedings of the 1994 IEEE International Conference on Robotics and automation, San Diego, USA, 8–13 May 1994.

Innocenti

Castelli

V. P.

, ‘Singularity-free evolution from one configuration to another in serial and fully-parallel manipulators’ Trans. ASME, J. Mech. Des. 120 3 (1998): 73–79.

Bandyopadhyay

Ghosal

, ‘Analysis of configuration space singularities of closed-loop mechanisms and parallel manipulators’ Mech. Mach. Theory 39 5 (2004): 519–544.

Merlet

J. P.

, Parallel manipulators part 2: Singular configurations and Grassmann geometry (1988): (Sophia Antipolis INRIA France).

Merlet

J. P.

, ‘Singular configurations of parallel manipulators and Grassmann geometry’ Int. J. Robot. Res. 8 5 (1989): 45–56.

Takeda

Funabashi

, ‘Kinematics and static characteristics of in-parallel actuated manipulators at singular points and in their neighborhood’ JSME Int. J. C 39 1 (1996): 85–93.

10.

Huang

Zhao

Wang

, ‘Kinematic principle and geometrical condition of general-linear-complex special configuration of parallel manipulators’ Mech. Mach. Theory 34 8 (1999): 1171–1186.

11.

Huang

, ‘Singularity analysis of general-linear-complex for 3/6-SPS Stewart robot’ Chin. J. Mech. Eng. 10 9 (1999): 997–1000.

12.

Hao

F. L.

McCarthy

J. M.

, ‘Conditions for line-based singularities in spatial platform manipulators’ J. Robot. Syst. 15 1 (1998): 43–55.

13.

Müller

, ‘Manipulability and static stability of parallel manipulators’ Multibody Syst. Dyn. 9 1 (2003): 1–23.

14.

Kieffer

, ‘Differential analysis of bifurcations and isolated singularities for robots and mechanisms’ IEEE J. Robot. Autom. 10 1 (1994): 1–10.

15.

Gregorio

D. R.

, ‘Singularity-locus expression of a class of parallel mechanisms’ Robotica 20 3 (2002): 323–328.

16.

Sefrioui

Gosselin

, ‘On the quadratic nature of the singularity curves of planar three- degree-of-freedom parallel manipulators’ Mech. Mach. Theory 30 2 (1995): 533–551.

17.

Gosselin

C. M.

Wang

, ‘Singularity loci of planar parallel manipulators’ In Proceedings of the NinthWorld Congress on the Theory of machines and mechanisms, Milano, Italy, 1995.

18.

Huang

Cao

, ‘Property identification of the singularity loci of a class of Gough–Stewart manipulator’ Int. J. Robot. Res. 24 (2002): 675–685.

19.

Wolf

Shoham

, ‘Investigation of parallel manipulators using linear complex approximation’ J. Mech. Des. 125 3 (2003): 564–572.

20.

St-Onge

B. M.

Gosselin

, ‘Singularity analysis and representation of the general Gough–Stewart platform’ Int. J. Robot. Res. 19 3 (2000): 271–288.

21.

H. D.

Gosselin

C. M.

Richard

M. J.

St-Onge

B. M.

, ‘Analytic form of the six-dimensional singularity locus of the general Gough-Stewart platform’ Trans. ASME, J. Mech. Des. 128 1 (2006): 279–287.

22.

Bandyopadhyay

Ghosal

, ‘Geometric characterization and parametric representation of the singularity manifold of a 6–6 Stewart platform manipulator’ Mech. Mach. Theory 41 11 (2006): 1377–1400.

23.

Wang

Y. X.

Y. T.

, ‘Disturbed configuration bifurcation characteristics of Gough–Stewart parallel manipulators at singular points’ J. Mech. Des. 130 2 (2008): 022304.

24.

Wang

Y. X.

Wang

Y. M.

, ‘Configuration bifurcations analysis of six degree-of-freedom symmetrical Stewart parallel mechanisms’ J. Mech. Des. 127 1 (2005): 70–77.

25.

Wang

Y. X.

Wang

Y. M.

Chen

Y. S.

Huang

, ‘Research on loss of controllability of Stewart parallel mechanisms at bifurcation points’ Chin. J. Mech. Eng. 41 7 (2005): 40–49.