An experimental and numerical study of the spray from an air-assisted fuel injector in a direct-injection spark ignition (DISI) engine is presented. The experiments are performed using ultraviolet laser diagnostics in a motoring optical engine that is a DISI variant of a production port-fuel-injected engine. Non-optical single-cylinder firing engine results of experiments and simulations are also presented. Recent related work by the present authors has shown that, under design conditions, the air-assisted injector exhibits strong coupling between the liquid and gas phases. It results in a filled-in conical spray of relatively fine atomization and low penetration, with liquid and vapour fuel concentrations close to the centrally located injector and spark plug, as required for lean stratified operation. This paper shows the strong effect of increasing the chamber temperature on spray evaporation and penetration. This observed temperature effect shows that spray evaporation should vary significantly during cold start. Exhaust gas recirculation (EGR) may also have a beneficial effect on DISI engine performance through enhanced spray evaporation, although this is difficult to verify experimentally. If true, this effect of EGR is a separate mechanism to the known beneficial effects of EGR in air-assisted DISI engines.
CostlowT.A new focus on emissions. Automot. Engng Int., December 2006, 28–32.
2.
SmythJ. G.SczomakD. P.IndraF.Zentraleinspritzung - die Zukunft der Direkteinspritzung? (Central injection - the heart of the next generation DI-gasoline engine?). In 10 Aachener Kolloquium Fahrzeug- und Motorentechnik2001, pp. 791–816 (Forschungsgesellschaft Kraftfahrwesen Aachen mbH, Aachen, Germany).
3.
CathcartG.RailtonD.Improving robustness of spray guided DI combustion systems: the air-assisted approach. JSAE paper 2001-5360, 2001.
4.
CathcartG.TubbJ.Application of air assisted direct fuel injection to pressure charged gasoline engines. SAE Paper 2002–01–0705, 2002.
5.
CathcartG.HoustonR.AhernS.The potential of gasoline DI for small displacement 4-stroke motorcycle applications. SAE Paper 2004–32–0098, 2004.
6.
JinS. H.BrearM. J.ZakisG.WatsonH. C.CarlisleH.An experimental study of the spray from an air-assisted, direct fuel injector. Proc. IMechE, Part D: J. Automobile Engineering, 2008 (submitted for publication).
7.
CathcartG.ZavierC.Fundamental characteristics of an air-assisted DI combustion system as applied to 4-stroke automotive gasoline engines. SAE Paper 2000–01–0256, 2000.
8.
MurdochP.WigleyG.HeathJ.PutcherG.A combined CFD and experimental analysis of the spray produced by an air-assisted GDI Injector. In Proceedings of the 16th Annual Conference on Liquid atomization and spray systems (ILASS-Europe 2000), Darmstadt, Germany, 11–13 September 2000 (ILASS-Europe Onlus, Naples, Italy).
9.
BorettiA.JinS. H.ZakisG.BrearM. J.AttardW.WatsonH.CarlisleH.BryceW.Experimental and numerical study of an air assisted fuel injector for a D.I.S.I. engine. SAE Paper 2007–01–1415, 2007.
10.
LeongM. Y.McDonellV. G.SamuelsenG. S.Mixing of an air blast-atomized fuel spray injected into a cross flow of Air. Report NASA/CR-2000–210467, National Aeronautics and Space Administration, 2000.
11.
JermyM. C.GreenhalghD. A.Planar drop sizing by elastic and fluorescence scattering in sprays too dense for phase Doppler measurement. Appl. Physics B., 2000, 71, 703–710.
12.
Le GalP.FarrugiaN.GreenhalghD. A.Laser sheet drop sizing of dense sprays. Optics Laser Technol., 1999, 31, 75–83.
13.
MeisterG. F.AlajbegovicA.LaiM.YooJ.Transient simulation of DGI engine injector with needle movement. SAE Paper 2002–01–2663, 2002.
14.
CousinJ.RenW. M.NallyS.Recent developments in simulations of internal flows in high pressure swirl injectors. Oil Gas Sci. Technol. - Rev. IFP., 1999, 54(2), 227–231.
15.
MulemaneA.SubramaniyamS.LuP.HanJ.LaiM.PoolaR.Comparing cavitations in diesel injectors based on different modelling approaches. SAE Paper 2004–01–0027, 2004.
16.
MasudaR.FuyutoT.NagaokaM.von BergE.TatschlR.Validation of diesel fuel spray and mixture formation from nozzle internal flow calculation. SAE Paper 2005–01–2098, 2005.
17.
KongC.SenecalP.ReitzR.Developments in spray modelling in diesel and direct-injection gasoline engines. Oil Gas Sci. Technol. - Rev. IFP., 1999, 54(2), 197–204.
18.
SuhE.RutlandC.Numerical study of fuel/air mixture preparation in a GDI engine. SAE Paper 1999–01–3657, 1999.
19.
KongS.MarriottC.RutlandC.ReitzR.Experiments and CFD modelling of DI gasoline HCCI engine combustion. SAE Paper 2002–01–1925, 2002.
20.
ChryssakisC.AssanisD.LeeJ.NishidaK.Fuel spray simulation of high-pressure swirl-in-jector for DISI engines and comparison with laser diagnostic measurements. SAE Paper 2003–01–0007, 2003.
21.
IyerC.HanZ.YiJ.CFD modelling of a vortex induced stratification combustion (VISC) system. SAE Paper 2004–01–0550, 2004.
22.
SkogsbergM.DahlanderP.LindgrenR.DenbrattI.Effects of injector parameters on mixture formation for multi-hole nozzles in a spray-guided gasoline DI engine. SAE Paper 2005–01–0097, 2005.
23.
AssanisD. N.HongS. J.NishimuraA.PapageorgakisG.VanzieleghemB.Studies of spray break-up and mixture stratification in a gasoline DI engine using KIVA-3V. Trans. ASME J. Engng Gas Turbines Power, 2000, 122, 485–492.
StantonD. W.RutlandC. J.Multi-dimensional modelling of heat and mass transfer of fuel films resulting from impinging sprays. SAE Paper 980132, 1998.
26.
RajuM. S.Numerical investigation of various atomization models in the modelling of a spray flame. Report NASA/CR-2005–214033, National Aeronautics and Space Administration, 2005; also Report AIAA-2006–0176, American Institute of Aeronautics and Astronautics, 2006.
27.
RaiuM. S.LSPRAY-II: a Lagrangian spray module. Report NASA/CR-2004–212958, National Aeronautics and Space Administration, 2004.
28.
GroverR. O.AssanisD. N.A spray wall impingement model based upon conservation principles. In Proceedings of the Fifth International Symposium on Diagnostics and Modelling of Combustion in Internal Combustion Engines (COMODIA 2001), Nagoya, Japan, July 2001, pp. 551–559.
29.
HabchiC.FoucartH.BaritaudT.Influence of the wall temperature on the mixture preparation in DI gasoline engines. Oil Gas Sci. Technol. - Rev. IFP., 1999, 54(2), 211–222.
30.
WangY.-P.WilkinsonG. B.DrallmeierJ. A.Parametric study on the fuel film break-up of a cold start PFI engine. Expl Fluids, 2004, 37, 385–398.
BorettiA.Experimental study of a two phase flow in the near field of an air blast atomizer. In Proceedings of the ASME-ASCE Mechanics Conference Forum on Turbulent flows, 1989, La Jolla, California, USA, July 1989, Vol. 76, pp. 101–106 (American Society of Mechanical Engineers, New York).
34.
MiyagawaH.Low emission combustion for spray-guided direct injection gasoline engine. In Proceedings of the FISITA 2006 World Automotive Congress, Yokohama, Japan, October2006, Paper F2006P147.
35.
HeywoodJ. B.Internal combustion engine fundamentals, 1989, pp. 837–838 (McGraw-Hill, New York).
