Stamina of a non-gasketed flange joint under combined internal pressure and axial loading

Abstract

The performance of a bolted flange joint is characterized mainly by its ‘strength’ and ‘sealing capability’. A number of numerical and experimental studies have been conducted to study these characteristics under internal pressure loading conditions alone. However, limited work is found in the literature under conditions of combined internal pressure and axial loading. The effect of external, axial loading pressure being unknown, the optimal performance of the bolted flange joint cannot be achieved. Current design codes do not address the effects of axial loading on structural integrity and sealing ability. To study joint strength and sealing capability under combined loading conditions, an extensive experimental and numerical study of a non-gasketed flange joint was carried out. Actual joint load capacity was determined at both design and test stages with the maximum external axial loading that can be applied for safe joint performance. Experimental and numerical results have been compared and overall joint performance and behaviour is discussed in detail.

Keywords

non-gasketed combined bolt-up operating axial sealing strength

Get full access to this article

View all access options for this article.

References

1 BSG 1560:1989. Steel pipe flanges for the petroleum industry. British Standards Institution, London, UK.

2 ASME boiler and pressure vessel code section VIII, 1998 (American Society of Mechanical Engineers, New York, USA).

Abid

Nash

D. H.

Comparative study of the behaviour of conventional gasketed and compact non-gasketed flanged pipe joints under bolt up and operating conditions. Int. J. Press. Vessels Pip., 2004, 80, 831–841.

Abid

Experimental and Analytical studies of conventional (gasketed) and unconventional (non gasketed) flanged pipe joints (with special emphasis on the engineering of ‘joint strength’ and ‘sealing’) PhD Thesis, 2000.

Webjörn

Flange design in Sweden. In the Petrochemical Mechanical Engineering Conference, American Society of Mechanical Engineers, Philadelphia, USA, 1967, pp. 17–20.

Webjörn

The bolted joint - a series of problems Linköping Studies in Science and Technology, Dissertation No. 130, 1985.

Abid

Nash

D. H.

Webjörn

The stamina of non-gasketed flanges. In the International Conference on Fatigue, 2000, Cambridge, UK, pp. 575–584.

Abid

Nash

D. H.

A parametric study of metal-to-metal contact flanges with optimised geometry for safe stress and no-leak conditions. Int. J. Press. Vessels Pip., 2004, 81, 67–74.

Abid

Determination of safe operating conditions for non-gasketed flange joint under combined internal pressure and temperature. Int. J. Mech. Mater. Des., 2005, 2, 129–140.

10.

Abid

Design and analysis of non-gasketed bolted flanged pipe joint under combined internal pressure and temperature loading. In the 3rd BSME-ASME International Conference on Thermal Engineering, Dhaka, Bangladesh, 20–22 December 2006.

11.

Morohoshi

Sawa

On the characteristics of rectangular bolted flanged connections with gaskets subjected to external tensile loads and bending moments. J. Press. Vessel Technol. Trans. ASME, 1994, 116(2), 207–215.

12.

Fukuoka

Takaki

Three dimensional finite element analysis of pipe flange - effect of flange interface geometry. ASME Press. Vessel Piping, 1998, 367, 61–67.

13.

13 ASME boiler and pressure vessel code section II, part D, 1998, (American Society of Mechanical Engineers, New York, USA).

14.

14 BS 3692:1967. Specifications for ISO metric precision hexagonal bolts, screws and nuts. British Standards Institution (BSI), London, UK.

15.

Spence

Macfarlane

D. M.

Tooth

A. S.

Metal-to-metal full face taper hub flanges: Finite-element model evaluation and preliminary plastic analysis. Proc. Instn Mech. Engrs Part E: J. Process Mechanical Engineering, 1998, 212, 57–69.

16.

16 ANSYS elements manual, seventh edition, 2004 (ANSYS Inc., USA).

17.

Spence

Tooth

A. S.

Pressure vessel design - concepts and principles, 1994 (E & FN Spon, London, New York).

18.

18 PD 5500:1997. Unfired fusion welded pressure vessels, British Standards Institution (BSI), London, UK.