Effect of the turning angle on the flow and performance characteristics of long S-shaped circular diffusers

Abstract

The effect of the turning angle on the flow and performance characteristics of long S-shaped circular diffusers (length-inlet diameter ratio, L/D_i = 11:4) having an area ratio of 1.9 and centre-line length of 600 mm has been established. The experiments are carried out for three S-shaped circular diffusers having angles of turn of 15°/15°, 22.5°/22.5° and 30°/30°. Velocity, static pressure and total pressure distributions at different planes along the length of the diffusers are measured using a five-hole impact probe. The turbulence intensity distribution at the same planes is also measured using a normal hot-wire probe. The static pressure recovery coefficients for 15°/15°, 22.5°/22.5° and 30°/30° diffusers are evaluated as 0.45, 0.40 and 0.35 respectively, whereas the ideal static pressure recovery coefficient is 0.72. The low performance is attributed to the generation of secondary flows due to geometrical curvature and additional losses as a result of the high surface roughness (~0.5 mm) of the diffusers. The pressure recovery coefficient of these circular test diffusers is comparatively lower than that of an S-shaped rectangular diffuser of nearly the same area ratio, even with a larger turning angle (90°/90°), i.e. 0.53. The total pressure loss coefficient for all the diffusers is nearly the same and seems to be independent of the angle of turn. The flow distribution is more uniform at the exit for the higher angle of turn diffusers.

Keywords

turning angle flow performance characteristics long S-shaped circular diffusers

Get full access to this article

View all access options for this article.

References

Waitman

B. A.

Reneau

L. R.

Kline

S. J.

Effect of inlet conditions on performance of two-dimensional subsonic diffusers. Trans. ASME, J. Basic Engng, 1961, 83, 349–360.

Fox

R. W.

Kline

S. J.

Flow regimes in curved subsonic diffusers. Trans. ASME, J. Basic Engng, 1962, 84, 303–311.

Miller

D. S.

Internal Flow Systems, 1978, BHRA Fluid Engineering Series 5 (BHRA Fluid Engineering).

Sullery

R. K.

Chandra

Muralidhar

Performance comparison of straight and curved diffuser. Defense Sci. J., 1983, 104, 195–203.

Kwong

A. H.M.

Dowling

A. P.

Unsteady flow in diffusers. Trans. ASME, J. Fluid Engng, 1994, 116, 842–846.

Berger

S. A.

Talbot

Yao

L. S.

Flow in curved pipes. Ann. Rev. Fluid Mechanics, 1983, 15, 461–512.

Eustice

Flow of water in curved pipes. Proc. R. Soc. Lond., Ser. A, 1910, 84, 107–118.

Eustice

Experiments of streamline motion in curved pipes. Proc. R. Soc. Lond., Ser. A, 1911, 85, 119–131.

Melling

Whitelaw

J. H.

Turbulent flow in a rectangular duct. J. Fluid Mechanics, 1976, 78, 289–315.

10.

Ito

Friction factors for turbulent flow in curved pipes. Trans. ASME, J. Basic Engng, 1959, 81, 123–134.

11.

Murakami

Shimizu

Asymmetric swirling flow in composite pipe bends. Bull. Jap. Soc. Mech. Engrs, 1978, 21, 1144–1151.

12.

Humphrey

J. A. C.

Taylor

A. M.K.P.

Whitelaw

J. H.

Laminar flow in a square duct with strong curvature. J. Fluid Mechanics, 1977, 83, 509–527.

13.

Humphrey

J. A. C.

Whitelaw

J. H.

Yee

Turbulent flow in a square duct with strong curvature. J. Fluid Mechanics, 1981, 103, 443–463.

14.

Nikuradse

Gesetzmaßigkeit der turbulenten stromung in glatten Rohren. Forschungsheft, 1932, 356.

15.

Rowe

Measurements and computations of flow in pipe bends. J. Fluid Mechanics, 1970, 43, 771–783.

16.

Bansod

Bradshaw

The flow in S-shaped ducts. Aeronaut. Q., 1972, 23, 131–140.

17.

Johnston

J. P.

Straight diffuser effectiveness data and its application to curved diffuser design employing the streamline curvature method. Technical Note 13, Ingersol-Rand Company, 1956.

18.

Sagi

C. J.

Johnston

J. P.

The design and performance of two-dimensional curved diffusers. Trans. ASME, J. Basic Engng, 1967, 89, 715–731.

19.

Rojas

Whitelaw

J. H.

Yianneskis

Developing flow in S-shape diffuser. Part II, circular cross-section diffuser. Publication FS/83/28, Department of Mechanical Engineering Imperial College of Science and Technology, London, 1983.

20.

Whitelaw

J. H.

S. C.

M. Turbulent flow characteristics in an S-shaped diffusing duct. Flow Measmt Instrum., 1993, 4, 171–179.

21.

Majumdar

Mohan

Singh

S. N.

Agrawal

D. P.

Experimental study of flow in high aspect ration 90 degree curved diffuser. Trans. ASME, J. Fluid Engng, 1998, 120, 83–89.

22.

Majumdar

Singh

S. N.

Agrawal

D. P.

Flow characteristics in a large area ratio curved diffuser. Proc. Instn Mech. Engrs, Part G: J. Aerospace Engineering, 1996, 210(91), 65–75.

23.

Majumdar

Singh

S. N.

Agrawal

D. P.

Flow characteristics in S-shaped diffusing duct. Int. J. Turbo and Jet Engines, 1997, 14, 45–57.

24.

Majumdar

Singh

S. N.

Agrawal

D. P.

Flow structure in a 180° curved diffusing duct. Arabian J. Sci. Engng, 1999, 24, 79–87.

25.

Anand

R. B.

Rai

Singh

S. N.

Sharma

O. P.

Flow characteristics of low aspect ratio 90°/90° S-shaped diffuser. J. Aeronaut. Soc. India, 2001, 53, 239–252.

26.

Anand

R. B.

Rai

Singh

S. N.

Flow and performance characteristics of 22.5°/22.5° S-shaped circular diffuser. In Proceedings of the 28th National Conference on Fluid Mechanics and Fluid Power, Chandigarh, India, December 2001, pp. 364–371.

27.

Bryer

D. W.

Pankhurst

R. C.

Pressure-Probe Methods for Determining Wind Speed and Flow Direction, 1971 (Her Majesty's Stationery Office, London).

28.

Majumdar

Flow investigation in curved diffusers. PhD thesis, Department of Applied Mechanics, Indian Institute of Technology, Delhi, India, 1994.

29.

Kline

S. J.

The purposes of uncertainty analysis. Trans. ASME, J. Fluid Engng, 1985, 107, 153–160.

30.

Sovran

Klomp

E. D.

Experimentally determined optimum geometries for rectilinear diffuser with rectangular conical or annular cross-section. In Proceedings of Symposium on The Fluid Mechanics of Internal Flow, General Motors Research Laboratories, Warren, Michigan, 1965.