This study focuses on the micromechanical prediction of temperature-dependent elastic properties of a composite made of a polypropylene matrix reinforced with discontinuous glass fibers. Firstly, an experimental investigation of the mechanical behavior is presented. Specimen are cut from injection-molded rectangular plates using a pattern based on fiber orientation. The microstructure is investigated by X-ray tomography at the specimen center and an average orientation tensor is calculated. Tensile tests are performed over a temperature range from ambient temperature to 85℃ and dispersion of mechanical properties is rather low; moreover, they are representative of the ones measured out of an industrial injected part. Then, the evolution of elastic properties with orientation and temperature is analyzed and compared with numerical predictions calculated with Mori–Tanaka homogenization scheme.
KlimkeitBNadotYCastagnetS, et al.Multiaxial fatigue life assessment for reinforced polymers. Int J Fatigue2011; 33: 766–780.
2.
BernasconiADavoliPArmanniC. Fatigue strength of a clutch pedal made of reprocessed short glass fibre reinforced polyamide. Int J Fatigue2010; 32: 100–107.
3.
SonsinoCMMoosbruggerE. Fatigue design of highly loaded short-glass-fibre reinforced polyamide parts in engine compartments. Int J Fatigue2008; 30: 1279–1288.
4.
SunXLaseckiJZengD, et al.Measurement and quantitative analysis of fiber orientation distribution in long fiber reinforced part by injection molding. Polym Test2015; 42: 168–174.
5.
Schijve W. Common errors and honest materials comparison for long glass PP materials. In: International AVK conference for reinforced plastics and thermoset molding compounds, Baden-Baden, Germany, 2002, pp. 17–18.
6.
Lopez-ManchadoMAArroyoM. Thermal and dynamic mechanical properties of polypropylene and short organic fiber composites. Polymer2000; 41: 7761–7767.
7.
AshoriAMenbariSBahramiR. Mechanical and thermo-mechanical properties of short carbon fiber reinforced polypropylene composites using exfoliated graphene nanoplatelets coating. J Ind Eng Chem2016; 38: 37–42.
8.
DoV-TNguyen-TranH-DChunD-M. Effect of polypropylene on the mechanical properties and water absorption of carbon-fiber-reinforced-polyamide-6/polypropylene composite. Compos Struct2016; 150: 240–245.
9.
Lopez D, Thuillier S, Grohens Y, et al. Anisotropic mechanical behavior of an injection molded short fiber reinforced thermoplastic. In: AIP conference proceedings., 2016, p. 060007. Nantes: AIP Publishing.
10.
Dray Bensahkoun D. Prediction of the thermoelastic properties of an injection molded short-fiber composite. Thesis, France,2006.
11.
BernasconiADavoliPBasileA, et al.Effect of fibre orientation on the fatigue behaviour of a short glass fibre reinforced polyamide-6. Int J Fatigue2007; 29: 199–208.
12.
Notta-CuvierDLauroFBennaniB, et al.Damage of short-fibre reinforced materials with anisotropy induced by complex fibres orientations. Mech Mater2014; 68: 193–206.
13.
MortazavianSFatemiA. Effects of fiber orientation and anisotropy on tensile strength and elastic modulus of short fiber reinforced polymer composites. Compos Part B: Eng2015; 72: 116–129.
14.
LaunayAMarcoYMaitournamMH, et al.Cyclic behavior of short glass fiber reinforced polyamide for fatigue life prediction of automotive components. Procedia Eng Conf Proc2010; 2: 901–910.
15.
Gehring F, Bouchart V, Dinzart F, et al. Etude expérimentale et modélisation du comportement de polymères thermoplastiques renforcés: polypropylène chargé de fibres de chanvre. In: 20ème Congrès Français de Mécanique, Besançon, France, 2011.
16.
AraoYYumitoriSSuzukiH, et al.Mechanical properties of injection-molded carbon fiber/polypropylene composites hybridized with nanofillers. Compos Part Appl Sci Manuf2013; 55: 19–26.
17.
De MonteMMoosbruggerEQuaresiminM. Influence of temperature and thickness on the off-axis behaviour of short glass fibre reinforced polyamide 6.6 – cyclic loading. Compos Part A: Appl Sci Manuf2010; 41: 1368–1379.
18.
LaunayAMaitournamMHMarcoY, et al.Multiaxial fatigue models for short glass fiber reinforced polyamide – part I: nonlinear anisotropic constitutive behavior for cyclic response. Int J Fatigue2013; 47: 382–389.
19.
JainAPaepegemWVVerpoestI, et al.A statistical treatment of the loss of stiffness during cyclic loading for short fiber reinforced injection molded composites. Compos Part B : Eng2016; 103: 40–50.
20.
Notta-CuvierDNciriMLauroF, et al.Coupled influence of strain rate and heterogeneous fibre orientation on the mechanical behaviour of short-glass-fibre reinforced polypropylene. Mech Mater2016; 100: 186–197.
21.
BarbosaSEKennyJM. Analysis of the relationship between processing conditions - fiber orientation - final properties in short fiber reinforced polypropylene. J Reinf Plast Compos1999; 18: 6731–6844.
22.
MouhmidBImadABenseddiqN, et al.A study of the mechanical behaviour of a glass fibre reinforced polyamide 6,6: Experimental investigation. Polym Test2006; 25: 544–552.
23.
MortazavianSFatemiA. Fatigue behavior and modeling of short fiber reinforced polymer composites including anisotropy and temperature effects. Int J Fatigue2015; 77: 12–27.
24.
ŞerbanDAWeberGMarşavinaL, et al.Tensile properties of semi-crystalline thermoplastic polymers: effects of temperature and strain rates. Polym Test2013; 32: 413–425.
25.
ZhaiZGröschelCDrummerD. Tensile behavior of quasi-unidirectional glass fiber/polypropylene composites at room and elevated temperatures. Polym Test2016; 54: 126–133.
26.
TeixeiraDGiovanelaMGonellaLB, et al.Influence of injection molding on the flexural strength and surface quality of long glass fiber-reinforced polyamide 6.6 composites. Mater Des2015; 85: 695–706.
27.
CoulonALafrancheEDouchainC, et al.Flexural creep behaviour of long glass fibre reinforced polyamide 6.6 under thermal-oxidative environment. J Compos Mater2016; 0: 0–14.
28.
LafrancheECoulonAKrawczakP, et al.A microstructural approach for modelling flexural properties of long glass fibre reinforced polyamide 6.6. J Compos Mater2016; 51: 3–16.
29.
RezaeiFYunusRIbrahimNA. Effect of fiber length on thermomechanical properties of short carbon fiber reinforced polypropylene composites. Mater Des2009; 30: 260–263.
AlbrechtKBaurEEndresH-J, et al.Measuring fibre orientation in sisal fibre-reinforced, injection moulded polypropylene – pros and cons of the experimental methods to validate injection moulding simulation. Compos Part A: Appl Sci Manuf2017; 95: 54–64.
32.
DeanAReinosoJSahraeeS, et al.An invariant-based anisotropic material model for short fiber-reinforced thermoplastics: coupled thermo-plastic formulation. Compos Part A: Appl Sci Manuf2016; 90: 186–199.
AdvaniSGTucker IIICL. The use of tensors to describe and predict fiber orientation in short fiber composites. J Rheol1987; 31: 751–784.
35.
AndriyanaABillonNSilvaL. Mechanical response of a short fiber-reinforced thermoplastic: Experimental investigation and continuum mechanical modeling. Eur J Mech – A Solids2010; 29: 1065–1077.
36.
OgiermanWKokotG. A study on fiber orientation influence on the mechanical response of a short fiber composite structure. Acta Mech2016; 227: 173–183.
37.
ParenteauTBertevasEAusiasG, et al.Characterisation and micromechanical modelling of the elasto-viscoplastic behavior of thermoplastic elastomers. Mech Mater2014; 71: 114–125.
38.
EftekhariMFatemiA. Creep behavior and modeling of neat, talc-filled, and short glass fiber reinforced thermoplastics. Compos Part B : Eng2016; 97: 68–83.
39.
Lopez D. Comportement d'un thermoplastique renforcé de fibres de verre soumis à des chargements thermomécaniques. Thesis, Université Bretagne Sud, France, 2018.
40.
MoriTTanakaK. Average stress in matrix and average elastic energy of materials with misfitting inclusions. Acta Metall1973; 21: 571–574.
41.
Digimat 2018 version 4.1.2. Linear and nonlinear multi-scale material software, e-Xstream engineering, MSC software company. www.e-xstream.com/.
